No obsession over 6 o'clock position.
However, at the 7:30 position the wings aren't fully engaged and that
doesn't seem good.
I'd settle for 6:30 or even 6:45 ;-)
Peter
On 13-06-05 7:05 AM, Dave B wrote:
WHY are you obsessing over "6 o'clock"??
On Mon, Jun 3, 2013 at 8:42 AM, Benjamin McCafferty <[email protected]
<mailto:[email protected]>> wrote:
Hey Peter,
Wasn't trying to bust your chops. Each time I read "basket" in
your original, I was picturing the part that holds coffee. I just
wanted to clarify that I now understand what you meant and that
hopefully my response made sense too. No offense intended.
best,
bmc
Sent from my apple IIe
On Jun 3, 2013, at 8:13, Mark Carter-Piff <[email protected]
<mailto:[email protected]>> wrote:
It sounds like the new gasket is thicker than the old one (which
would make sense) and that the portafilter handle is "seating"
earlier than the old one. Which would also make sense.
Have I got it correct?
On Sun, Jun 2, 2013 at 6:22 PM, <[email protected]
<mailto:[email protected]>> wrote:
Today's Topic Summary
Group: http://groups.google.com/group/brewtus/topics
* Trouble fitting replacement gasket
<#13f0ab3ecae0425a_13f07a10891fa954_group_thread_0> [1
Update]
Trouble fitting replacement gasket
<http://groups.google.com/group/brewtus/t/8794fcfd23d0b634>
Peter Sharpe <[email protected] <mailto:[email protected]>>
Jun 01 04:00PM -0700
Sorry about the confusion. I think of the screen as just,
well, the
screen itself not what it is attached to. But let me
restate things with
the proper terminology.
The screen is a bit loose when there is no gasket. That
is, I can fully
insert the screen and then slide it back and forth. Not
too far, but
there is slack there.
The gasket was inserted with beveled side up.
That gasket and screen were installed about 2 weeks ago
and I lived with
the handle at 7:30 to see if it would gradually seat
fully but I didn't
notice any change after that time.
I used a portafilter without basket to push the gasket up
as far as I
could. Then I added the basket to the portafilter and
pushed again with
it. (When I say "push" I mean that I inserted the
portafilter and
rotated it with the wings in their slots.
The previous time that I inserted this new gasket and
screen I applied
plenty of force with all kinds of blunt instruments but
nothing would
make it budge.
The machine works and does not leak. I was hoping for
something closer
to 6 o'clock though.
Thanks for your reply.
Peter
On 13-06-01 1:38 PM, Ben McCafferty wrote:
You received this message because you are subscribed to the
Google Group brewtus.
You can post via email <mailto:[email protected]>.
To unsubscribe from this group, send
<mailto:[email protected]> an empty message.
For more options, visit
<http://groups.google.com/group/brewtus/topics> this group.
--
You received this message because you are subscribed to the
Google Groups "Brewtus" group.
To unsubscribe from this group and stop receiving emails from
it, send an email to [email protected]
<mailto:brewtus%[email protected]>.
To post to this group, send email to [email protected]
<mailto:[email protected]>.
Visit this group at http://groups.google.com/group/brewtus?hl=en.
For more options, visit https://groups.google.com/groups/opt_out.
--
You received this message because you are subscribed to the
Google Groups "Brewtus" group.
To unsubscribe from this group and stop receiving emails from it,
send an email to [email protected]
<mailto:[email protected]>.
To post to this group, send email to [email protected]
<mailto:[email protected]>.
Visit this group at http://groups.google.com/group/brewtus?hl=en.
For more options, visit https://groups.google.com/groups/opt_out.
--
You received this message because you are subscribed to the Google
Groups "Brewtus" group.
To unsubscribe from this group and stop receiving emails from it,
send an email to [email protected]
<mailto:brewtus%[email protected]>.
To post to this group, send email to [email protected]
<mailto:[email protected]>.
Visit this group at http://groups.google.com/group/brewtus?hl=en.
For more options, visit https://groups.google.com/groups/opt_out.
--
You received this message because you are subscribed to the Google
Groups "Brewtus" group.
To unsubscribe from this group and stop receiving emails from it, send
an email to [email protected].
To post to this group, send email to [email protected].
Visit this group at http://groups.google.com/group/brewtus?hl=en.
For more options, visit https://groups.google.com/groups/opt_out.
--
You received this message because you are subscribed to the Google Groups
"Brewtus" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To post to this group, send email to [email protected].
Visit this group at http://groups.google.com/group/brewtus?hl=en.
For more options, visit https://groups.google.com/groups/opt_out.
