Tzafrir Cohen pravi: > On Wed, Nov 05, 2008 at 10:35:55AM +0100, Sebastijan Šilec wrote: > >> Hello >> We were using a quadbri card from Junghanns, and now bought openvox b800p >> >> I tried to compile briistuff with openvox qozap patch but no luck.... >> >> [EMAIL PROTECTED]:~# ztcfg -vvvv >> >> Zaptel Configuration >> ====================== >> >> SPAN 1: CCS/ AMI Build-out: 133-266 feet (DSX-1) >> SPAN 2: CCS/ AMI Build-out: 133-266 feet (DSX-1) >> SPAN 3: CCS/ AMI Build-out: 133-266 feet (DSX-1) >> SPAN 4: CCS/ AMI Build-out: 133-266 feet (DSX-1) >> SPAN 5: CCS/ AMI Build-out: 133-266 feet (DSX-1) >> SPAN 6: CCS/ AMI Build-out: 133-266 feet (DSX-1) >> SPAN 7: CCS/ AMI Build-out: 133-266 feet (DSX-1) >> SPAN 8: CCS/ AMI Build-out: 133-266 feet (DSX-1) >> >> Channel map: >> >> Channel 01: Clear channel (Default) (Slaves: 01) >> Channel 02: Clear channel (Default) (Slaves: 02) >> Channel 03: D-channel (Default) (Slaves: 03) >> Channel 04: Clear channel (Default) (Slaves: 04) >> Channel 05: Clear channel (Default) (Slaves: 05) >> Channel 06: D-channel (Default) (Slaves: 06) >> Channel 07: Clear channel (Default) (Slaves: 07) >> Channel 08: Clear channel (Default) (Slaves: 08) >> Channel 09: D-channel (Default) (Slaves: 09) >> Channel 10: Clear channel (Default) (Slaves: 10) >> Channel 11: Clear channel (Default) (Slaves: 11) >> Channel 12: D-channel (Default) (Slaves: 12) >> Channel 13: Clear channel (A-law) (Slaves: 13) >> Channel 14: D-channel (Default) (Slaves: 14) >> Channel 15: Clear channel (A-law) (Slaves: 15) >> Channel 16: D-channel (Default) (Slaves: 16) >> Channel 17: Clear channel (A-law) (Slaves: 17) >> Channel 18: D-channel (Default) (Slaves: 18) >> Channel 19: Clear channel (A-law) (Slaves: 19) >> Channel 20: D-channel (Default) (Slaves: 20) >> >> 20 channels configured. >> > > In later versions of Zaptel this misleading message was replaced with: > "[20] channels to configure." > > Up to this point it only showed what you wrote in zaptel.conf . > > >> ZT_SPANCONFIG failed on span 1: No such device or address (6) >> > > Oops . No span 1 . > > Do you actually see the card on lspci? Is the module loaded? > > >> I get this error. >> >> Any suggestions how to make an easiest transition between two cards? >> We have bristuff-0.3.0-PRE-1q installed >> > > There are newer versions of bristuff available. > lspci :
0000:01:01.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-8S] (rev 01) I'm using the old version of bristuff, because we have also a gsm module and everything is working ok, we would just like to replace the isdn card and keep the things intact if it is possible. Thank you. -- Sebastijan Šilec, sistemska podpora Predlog! Obiscite prenovljeno spletno stran http://www.agenda.si ODPRTA KODA IN LINUX STORITVE : POSLOVNE RESITVE : UPRAVLJANJE IT : INFRASTRUKTURA IT : IZOBRAZEVANJE : PROGRAMSKA OPREMA Visit our updated web page at http://www.agenda.si OPEN SOURCE AND LINUX SERVICES : BUSINESS SOLUTIONS : IT MANAGEMENT : IT INFRASTRUCTURE : TRAINING : SOFTWARE
begin:vcard fn;quoted-printable:Sebastijan =C5=A0ilec n;quoted-printable:=C5=A0ilec;Sebastijan org:Agenda OpenSystems d.o.o.;IT adr:;;Ul. Pohorskega bataljina 49;Maribor;;2000;Slovenija email;internet:[EMAIL PROTECTED] title:System Admin. note:www.agenda.si url:http://www.agenda.si version:2.1 end:vcard
_______________________________________________ Bristuff-users mailing list [email protected] http://lists.three-dimensional.net/mailman/listinfo/bristuff-users
