On 2020-12-11 15:14, Johan Huldtgren wrote:
> hello,
>
> i recently tried to upgrade one of my i386 boxes from an older 6.8 snap (~end
> of
> October timeframe) to the latest one (Dec 10th). First I used sysupgrade and
> when it gets to the part where it would normally print "Install, Upgrade,
> Shell"
> it simply started rolling:
>
> init: single user shell terminated, restarting
> init: single user shell terminated, restarting
> ...
>
> over and over again until the machine was power cycled. Figuring i might have
> gotten a bad snap I waited and tried again today, but I had the same
> experience.
> This time after the power cycle I tried manually running bsd.rd and this
> worked. I
> let it run through, but now after booting I am seeing that behaviour again:
>
> ------
>
> switching console to com0
> >> OpenBSD/i386 BOOT 3.44
> boot>
> booting hd0a:/bsd: 10009111+2417668+253960+0+1126400
> [680608+107+567232+603277]=0xef1198
> entry point at 0x201000
>
> [ using 1851800 bytes of bsd ELF symbol table ]
> Copyright (c) 1982, 1986, 1989, 1991, 1993
> The Regents of the University of California. All rights reserved.
> Copyright (c) 1995-2020 OpenBSD. All rights reserved. https://www.OpenBSD.org
>
> OpenBSD 6.8-current (GENERIC) #534: Thu Dec 10 20:15:49 MST 2020
> [email protected]:/usr/src/sys/arch/i386/compile/GENERIC
> real mem = 536363008 (511MB)
> avail mem = 510287872 (486MB)
> random: good seed from bootblocks
> mpath0 at root
> scsibus0 at mpath0: 256 targets
> mainbus0 at root
> bios0 at mainbus0: date 20/71/05, BIOS32 rev. 0 @ 0xfac40
> pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
> pcibios0: pcibios_get_intr_routing - function not supported
> pcibios0: PCI IRQ Routing information unavailable.
> pcibios0: PCI bus #0 is the last bus
> bios0: ROM list: 0xc8000/0xa800
> cpu0 at mainbus0: (uniprocessor)
> cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD" 586-class)
> 500 MHz, 05-0a-02
> cpu0: FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CFLUSH,MMX,MMXX,3DNOW2,3DNOW
> mtrr: K6-family MTRR support (2 registers)
> amdmsr0 at mainbus0
> pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
> 0:20:0: io address conflict 0x6100/0x100
> 0:20:0: io address conflict 0x6200/0x200
> pchb0 at pci0 dev 1 function 0 "AMD Geode LX" rev 0x31
> glxsb0 at pci0 dev 1 function 2 "AMD Geode LX Crypto" rev 0x00: RNG AES
> vr0 at pci0 dev 6 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 11, address
> 00:00:24:c9:58:4c
> ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
> 0x004063, model 0x0034
> vr1 at pci0 dev 7 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 5, address
> 00:00:24:c9:58:4d
> ukphy1 at vr1 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
> 0x004063, model 0x0034
> vr2 at pci0 dev 8 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 9, address
> 00:00:24:c9:58:4e
> ukphy2 at vr2 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
> 0x004063, model 0x0034
> vr3 at pci0 dev 9 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 12, address
> 00:00:24:c9:58:4f
> ukphy3 at vr3 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
> 0x004063, model 0x0034
> ral0 at pci0 dev 17 function 0 "Ralink RT2561S" rev 0x00: irq 15, address
> 00:12:0e:61:7f:b0
> ral0: MAC/BBP RT2561C, RF RT5225
> glxpcib0 at pci0 dev 20 function 0 "AMD CS5536 ISA" rev 0x03: rev 3, 32-bit
> 3579545Hz timer, watchdog, gpio, i2c
> gpio0 at glxpcib0: 32 pins
> iic0 at glxpcib0
> pciide0 at pci0 dev 20 function 2 "AMD CS5536 IDE" rev 0x01: DMA, channel 0
> wired to compatibility, channel 1 wired to compatibility
> wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFX4-8192>
> wd0: 4-sector PIO, LBA, 7815MB, 16007040 sectors
> wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
> pciide0: channel 1 ignored (disabled)
> ohci0 at pci0 dev 21 function 0 "AMD CS5536 USB" rev 0x02: irq 7, version
> 1.0, legacy support
> ehci0 at pci0 dev 21 function 1 "AMD CS5536 USB" rev 0x02: irq 7
> usb0 at ehci0: USB revision 2.0
> uhub0 at usb0 configuration 1 interface 0 "AMD EHCI root hub" rev 2.00/1.00
> addr 1
> isa0 at glxpcib0
> isadma0 at isa0
> com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> com0: console
> com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
> pckbc0 at isa0 port 0x60/5 irq 1 irq 12
> pckbc0: unable to establish interrupt for irq 12
> pckbd0 at pckbc0 (kbd slot)
> wskbd0 at pckbd0: console keyboard
> pcppi0 at isa0 port 0x61
> spkr0 at pcppi0
> nsclpcsio0 at isa0 port 0x2e/2: NSC PC87366 rev 10: GPIO VLM TMS
> gpio1 at nsclpcsio0: 29 pins
> npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
> usb1 at ohci0: USB revision 1.0
> uhub1 at usb1 configuration 1 interface 0 "AMD OHCI root hub" rev 1.00/1.00
> addr 1
> vscsi0 at root
> scsibus1 at vscsi0: 256 targets
> softraid0 at root
> scsibus2 at softraid0: 256 targets
> root on wd0a (14df1105db104991.a) swap on wd0b dump on wd0b
> init: /bin/sh on /etc/rc terminated abnormally, going to single user mode
> Enter pathname of shell or RETURN for sh:
> init: single user shell terminated, restarting
> Enter pathname of shell or RETURN for sh: /bin/sh
> init: single user shell terminated, restarting
> Enter pathname of shell or RETURN for sh:
> init: single user shell terminated, restarting
> Enter pathname of shell or RETURN for sh:
>
> ----
>
> Unfortunately I seem to have forgotten to save the previous bsd so I can't
> test
> booting it, but I did have a bsd.old from back in September and even booting
> that exhibits the same behaviour:
>
> ----
>
> Using drive 0, partition 3.
> Loading......
> probing: pc0 com0 com1 mem[639K 511M a20=on]
> disk: hd0+
> >> OpenBSD/i386 BOOT 3.44
> switching console to com0
> >> OpenBSD/i386 BOOT 3.44
> boot> bsd.old
> NOTE: random seed is being reused.
> booting hd0a:bsd.old: 10041879+2409476+253960+0+1110016
> [684001+107+566576+603005]=0xef3b3c
> entry point at 0x201000
>
> [ using 1854268 bytes of bsd ELF symbol table ]
> Copyright (c) 1982, 1986, 1989, 1991, 1993
> The Regents of the University of California. All rights reserved.
> Copyright (c) 1995-2020 OpenBSD. All rights reserved. https://www.OpenBSD.org
>
> OpenBSD 6.8-beta (GENERIC) #403: Tue Sep 15 12:45:32 MDT 2020
> [email protected]:/usr/src/sys/arch/i386/compile/GENERIC
> real mem = 536363008 (511MB)
> avail mem = 510279680 (486MB)
> random: good seed from bootblocks
> mpath0 at root
> scsibus0 at mpath0: 256 targets
> mainbus0 at root
> bios0 at mainbus0: date 20/71/05, BIOS32 rev. 0 @ 0xfac40
> pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
> pcibios0: pcibios_get_intr_routing - function not supported
> pcibios0: PCI IRQ Routing information unavailable.
> pcibios0: PCI bus #0 is the last bus
> bios0: ROM list: 0xc8000/0xa800
> cpu0 at mainbus0: (uniprocessor)
> cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD" 586-class)
> 500 MHz, 05-0a-02
> cpu0: FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CFLUSH,MMX,MMXX,3DNOW2,3DNOW
> mtrr: K6-family MTRR support (2 registers)
> amdmsr0 at mainbus0
> pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
> 0:20:0: io address conflict 0x6100/0x100
> 0:20:0: io address conflict 0x6200/0x200
> pchb0 at pci0 dev 1 function 0 "AMD Geode LX" rev 0x31
> glxsb0 at pci0 dev 1 function 2 "AMD Geode LX Crypto" rev 0x00: RNG AES
> vr0 at pci0 dev 6 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 11, address
> 00:00:24:c9:58:4c
> ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
> 0x004063, model 0x0034
> vr1 at pci0 dev 7 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 5, address
> 00:00:24:c9:58:4d
> ukphy1 at vr1 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
> 0x004063, model 0x0034
> vr2 at pci0 dev 8 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 9, address
> 00:00:24:c9:58:4e
> ukphy2 at vr2 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
> 0x004063, model 0x0034
> vr3 at pci0 dev 9 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 12, address
> 00:00:24:c9:58:4f
> ukphy3 at vr3 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
> 0x004063, model 0x0034
> ral0 at pci0 dev 17 function 0 "Ralink RT2561S" rev 0x00: irq 15, address
> 00:12:0e:61:7f:b0
> ral0: MAC/BBP RT2561C, RF RT5225
> glxpcib0 at pci0 dev 20 function 0 "AMD CS5536 ISA" rev 0x03: rev 3, 32-bit
> 3579545Hz timer, watchdog, gpio, i2c
> gpio0 at glxpcib0: 32 pins
> iic0 at glxpcib0
> pciide0 at pci0 dev 20 function 2 "AMD CS5536 IDE" rev 0x01: DMA, channel 0
> wired to compatibility, channel 1 wired to compatibility
> wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFX4-8192>
> wd0: 4-sector PIO, LBA, 7815MB, 16007040 sectors
> wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
> pciide0: channel 1 ignored (disabled)
> ohci0 at pci0 dev 21 function 0 "AMD CS5536 USB" rev 0x02: irq 7, version
> 1.0, legacy support
> ehci0 at pci0 dev 21 function 1 "AMD CS5536 USB" rev 0x02: irq 7
> usb0 at ehci0: USB revision 2.0
> uhub0 at usb0 configuration 1 interface 0 "AMD EHCI root hub" rev 2.00/1.00
> addr 1
> isa0 at glxpcib0
> isadma0 at isa0
> com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> com0: console
> com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
> pckbc0 at isa0 port 0x60/5 irq 1 irq 12
> pckbc0: unable to establish interrupt for irq 12
> pckbd0 at pckbc0 (kbd slot)
> wskbd0 at pckbd0: console keyboard
> pcppi0 at isa0 port 0x61
> spkr0 at pcppi0
> nsclpcsio0 at isa0 port 0x2e/2: NSC PC87366 rev 10: GPIO VLM TMS
> gpio1 at nsclpcsio0: 29 pins
> npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
> usb1 at ohci0: USB revision 1.0
> uhub1 at usb1 configuration 1 interface 0 "AMD OHCI root hub" rev 1.00/1.00
> addr 1
> vscsi0 at root
> scsibus1 at vscsi0: 256 targets
> softraid0 at root
> scsibus2 at softraid0: 256 targets
> root on wd0a (14df1105db104991.a) swap on wd0b dump on wd0b
> init: /bin/sh on /etc/rc terminated abnormally, going to single user mode
> Enter pathname of shell or RETURN for sh:
>
> ----
>
> this server doesn't do much at the moment so rebuilding it if I must isn't a
> big
> deal. Let me know if I can supply any further info to help debug the issue.
I realized that I could pxeboot older bsd.rd successfully but not current, so I
started fetching them backwards and this issue starts to occur on the Dec 8th
snapshot, Dec 7th I can boot. Below are the bsd.rd boots on each one.
--- December 8th snapshot ---
>> OpenBSD/i386 PXEBOOT 3.43
switching console to com0
>> OpenBSD/i386 PXEBOOT 3.43
boot> bsd.rd
booting tftp:bsd.rd: 3222039+1405952+3362824+0+475136
[312398+107+296496+291986]=0x8f11bc
entry point at 0x201000
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2020 OpenBSD. All rights reserved. https://www.OpenBSD.org
OpenBSD 6.8-current (RAMDISK_CD) #524: Sun Dec 6 21:22:12 MST 2020
[email protected]:/usr/src/sys/arch/i386/compile/RAMDISK_CD
real mem = 536408064 (511MB)
avail mem = 517402624 (493MB)
random: good seed from bootblocks
mainbus0 at root
bios0 at mainbus0: date 20/71/05, BIOS32 rev. 0 @ 0xfac40
pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc8000/0xa800
cpu0 at mainbus0: (uniprocessor)
cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD" 586-class) 500
MHz, 05-0a-02
cpu0: FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CFLUSH,MMX,MMXX,3DNOW2,3DNOW
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
0:20:0: io address conflict 0x6100/0x100
0:20:0: io address conflict 0x6200/0x200
pchb0 at pci0 dev 1 function 0 "AMD Geode LX" rev 0x31
"AMD Geode LX Crypto" rev 0x00 at pci0 dev 1 function 2 not configured
vr0 at pci0 dev 6 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 11, address
00:00:24:c9:58:4c
ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
vr1 at pci0 dev 7 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 5, address
00:00:24:c9:58:4d
ukphy1 at vr1 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
vr2 at pci0 dev 8 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 9, address
00:00:24:c9:58:4e
ukphy2 at vr2 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
vr3 at pci0 dev 9 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 12, address
00:00:24:c9:58:4f
ukphy3 at vr3 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
ral0 at pci0 dev 17 function 0 "Ralink RT2561S" rev 0x00: irq 15, address
00:12:0e:61:7f:b0
ral0: MAC/BBP RT2561C, RF RT5225
pcib0 at pci0 dev 20 function 0 "AMD CS5536 ISA" rev 0x03
pciide0 at pci0 dev 20 function 2 "AMD CS5536 IDE" rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFX4-8192>
wd0: 4-sector PIO, LBA, 7815MB, 16007040 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 ignored (disabled)
ohci0 at pci0 dev 21 function 0 "AMD CS5536 USB" rev 0x02: irq 7, version 1.0,
legacy support
ehci0 at pci0 dev 21 function 1 "AMD CS5536 USB" rev 0x02: irq 7
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "AMD EHCI root hub" rev 2.00/1.00
addr 1
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5 irq 1 irq 12
pckbc0: unable to establish interrupt for irq 12
pckbd0 at pckbc0 (kbd slot)
wskbd0 at pckbd0: console keyboard
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 configuration 1 interface 0 "AMD OHCI root hub" rev 1.00/1.00
addr 1
softraid0 at root
scsibus0 at softraid0: 256 targets
PXE boot MAC address 00:00:24:c9:58:4c, interface vr0
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
init: single user shell terminated, restarting
init: single user shell terminated, restarting
--- December 7th snapshot ---
penBSD/i386 PXEBOOT 3.43
switching console to com0
>> OpenBSD/i386 PXEBOOT 3.43
boot> bsd.rd
booting tftp:bsd.rd: 3217943+1405952+3362824+0+479232
[312399+107+296496+291986]=0x8f11bc
entry point at 0x201000
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2020 OpenBSD. All rights reserved. https://www.OpenBSD.org
OpenBSD 6.8-current (RAMDISK_CD) #522: Sun Dec 6 11:08:30 MST 2020
[email protected]:/usr/src/sys/arch/i386/compile/RAMDISK_CD
real mem = 536408064 (511MB)
avail mem = 517402624 (493MB)
random: good seed from bootblocks
mainbus0 at root
bios0 at mainbus0: date 20/71/05, BIOS32 rev. 0 @ 0xfac40
pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc8000/0xa800
cpu0 at mainbus0: (uniprocessor)
cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD" 586-class) 500
MHz, 05-0a-02
cpu0: FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CFLUSH,MMX,MMXX,3DNOW2,3DNOW
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
0:20:0: io address conflict 0x6100/0x100
0:20:0: io address conflict 0x6200/0x200
pchb0 at pci0 dev 1 function 0 "AMD Geode LX" rev 0x31
"AMD Geode LX Crypto" rev 0x00 at pci0 dev 1 function 2 not configured
vr0 at pci0 dev 6 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 11, address
00:00:24:c9:58:4c
ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
vr1 at pci0 dev 7 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 5, address
00:00:24:c9:58:4d
ukphy1 at vr1 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
vr2 at pci0 dev 8 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 9, address
00:00:24:c9:58:4e
ukphy2 at vr2 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
vr3 at pci0 dev 9 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 12, address
00:00:24:c9:58:4f
ukphy3 at vr3 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
ral0 at pci0 dev 17 function 0 "Ralink RT2561S" rev 0x00: irq 15, address
00:12:0e:61:7f:b0
ral0: MAC/BBP RT2561C, RF RT5225
pcib0 at pci0 dev 20 function 0 "AMD CS5536 ISA" rev 0x03
pciide0 at pci0 dev 20 function 2 "AMD CS5536 IDE" rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFX4-8192>
wd0: 4-sector PIO, LBA, 7815MB, 16007040 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 ignored (disabled)
ohci0 at pci0 dev 21 function 0 "AMD CS5536 USB" rev 0x02: irq 7, version 1.0,
legacy support
ehci0 at pci0 dev 21 function 1 "AMD CS5536 USB" rev 0x02: irq 7
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "AMD EHCI root hub" rev 2.00/1.00
addr 1
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5 irq 1 irq 12
pckbc0: unable to establish interrupt for irq 12
pckbd0 at pckbc0 (kbd slot)
wskbd0 at pckbd0: console keyboard
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 configuration 1 interface 0 "AMD OHCI root hub" rev 1.00/1.00
addr 1
softraid0 at root
scsibus0 at softraid0: 256 targets
PXE boot MAC address 00:00:24:c9:58:4c, interface vr0
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
erase ^?, werase ^W, kill ^U, intr ^C, status ^T
Welcome to the OpenBSD/i386 6.8 installation program.
Starting non-interactive mode in 5 seconds...
(I)nstall, (U)pgrade, (A)utoinstall or (S)hell? s
#
-----
thanks,
.jh
