Use braided copper for bonding but minimum AWG6 wire for external grounding and lightning protection.
Every single ground system in the N0AX book suggests wire not braid. The two are totally different animals From: BVARC <bvarc-boun...@bvarc.org> on behalf of Rick Hiller via BVARC <bvarc@bvarc.org> Date: Saturday, February 24, 2024 at 10:50 To: BRAZOS VALLEY AMATEUR RADIO CLUB <bvarc@bvarc.org> Cc: Rick Hiller <rickhille...@gmail.com> Subject: Re: [BVARC] Antenna prewire house John is correct....... Have a read of ARRL Publication by H. Ward Silver, N0AX, Grounding and Bonding for the Radio Amateur and The Radio Hotel in the BVARC Beacon Sept 2023 Conductors for Grounding written by the folks at Georgia Copper. find it on the BVARC.org Tech Pages at https://bvarc.org/rh/rh_2309.pdf 73...Rick W5RH On Fri, Feb 23, 2024 at 8:59 PM John Parmalee via BVARC <bvarc@bvarc.org<mailto:bvarc@bvarc.org>> wrote: I think copper strap is better. Look at any broadcast facility where there is high power and you will find copper strap.. Check out George Copper From: BVARC <bvarc-boun...@bvarc.org<mailto:bvarc-boun...@bvarc.org>> On Behalf Of Robert Polinski via BVARC Sent: Friday, February 23, 2024 12:31 PM To: 'BRAZOS VALLEY AMATEUR RADIO CLUB' <bvarc@bvarc.org<mailto:bvarc@bvarc.org>> Cc: Robert Polinski <emdhous...@suddenlinkmail.com<mailto:emdhous...@suddenlinkmail.com>> Subject: Re: [BVARC] Antenna prewire house Make sure that ether you or your electrician, run a #6 wire from the electrical ground to any ground rods you install at your ham system. They need to be bonded together. Robert From: BVARC <bvarc-boun...@bvarc.org<mailto:bvarc-boun...@bvarc.org>> On Behalf Of Rod Neumann via BVARC Sent: Thursday, February 22, 2024 12:37 PM To: BRAZOS VALLEY AMATEUR RADIO CLUB <bvarc@bvarc.org<mailto:bvarc@bvarc.org>> Cc: Rod Neumann <i...@adorstore.com<mailto:i...@adorstore.com>> Subject: Re: [BVARC] Antenna prewire house I'm not answering what you asked, but for a new 2nd story install I will suggest you put a good deep copper ground rod in the ground directly below the shack window and run a good copper conductor, I think wide flat copper braided is best (? is that still the consensus?), and ground all chassis to that ground. Being up on the second story can present RF-in-the-shack problems if you don't have a very good low inductance path to ground. ROD / W5IE Rod Neumann (832)444-0192 ALLogic Inc. / AdorStore PO Box 217 NEW ULM, TX 78950 On Thu, Feb 22, 2024 at 10:05 AM Chuck via BVARC <bvarc@bvarc.org<mailto:bvarc@bvarc.org>> wrote: Building new house 2 story with radio room upstairs was thinking of bringing cables in under the eve near the peek was looking for any advice and what type of device with the connectors to buy…..new to ham radio so not much experience any help appreciated . Chuck Hale KF5UXP ________________________________________________ Brazos Valley Amateur Radio Club BVARC mailing list BVARC@bvarc.org<mailto:BVARC@bvarc.org> http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org Publicly available archives are available here: https://www.mail-archive.com/bvarc@bvarc.org/ ________________________________________________ Brazos Valley Amateur Radio Club BVARC mailing list BVARC@bvarc.org<mailto:BVARC@bvarc.org> http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org Publicly available archives are available here: https://www.mail-archive.com/bvarc@bvarc.org/ -- Rick Hiller e-mail: rickhille...@gmail.com<mailto:rickhille...@gmail.com> Cell/VM/Text: 832-474-3713 Physical: 9031 Troulon Drive Houston, TX 77036
________________________________________________ Brazos Valley Amateur Radio Club BVARC mailing list BVARC@bvarc.org http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org Publicly available archives are available here: https://www.mail-archive.com/bvarc@bvarc.org/
