Posting on behalf of Dale. Please see the message below. Thanks,
Nimish ---------- Forwarded message ---------- From: "Gary, Dale E." <[email protected]> To: casper list <[email protected]> Cc: Date: Thu, 6 Jun 2013 00:40:25 +0000 Subject: netbooting ROACH2 Hi Casperites, I am setting up a ROACH2 rev2 for netbooting, and I think I am almost there, but the ROACH hangs during the boot process, which suggests either a setup problem or the wrong Image or filesystem. The uImage is uImage-r2borph3, and the filesystem is roach2-debian-fs-snapshot-24-10-2012.tar.gz. According to the output during the boot process (see below), I appear to have bootp and tftp set up correctly. Can anyone spot the problem based on this information, or suggest a way to get more information on what might have gone wrong? Perhaps something to do with the USB device? Thanks, Dale =======Output of boot process======== Waiting for PHY auto negotiation to complete.... done ENET Speed is 1000 Mbps - FULL duplex connection (EMAC0) BOOTP broadcast 1 DHCP client bound to address 192.168.24.121 Using ppc_4xx_eth0 device TFTP from server 192.100.16.206; our IP address is 192.168.24.121; sending through gateway 192.168.24.1 Filename 'uImage'. Load address: 0x4000000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ############ done Bytes transferred = 1390149 (153645 hex) ## Booting kernel from Legacy Image at 04000000 ... Image Name: Linux-2.6.25-svn3489 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 1390085 Bytes = 1.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK id mach(): done MMU:enter MMU:hw init MMU:mapin MMU:setio MMU:exit setup_arch: enter setup_arch: bootmem ocp: exit arch: exit Linux version 2.6.25-svn3489 (dave@lapster) (gcc version 4.2.2) #6 Fri Aug 12 09:36:28 SAST 2011 AMCC PowerPC 440EPx Roach Platform Zone PFN ranges: DMA 0 -> 131071 Normal 131071 -> 131071 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0 -> 131071 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 Kernel command line: console=ttyS0,115200 root=/dev/nfs rootpath=192.100.16.206:/srv/roach2_boot/etch ip=dhcp PID hash table entries: 2048 (order: 11, 8192 bytes) console [ttyS0] enabled Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 516608k available (2084k kernel code, 720k data, 132k init, 0k highmem) Mount-cache hash table entries: 512 BORPH version CVS-$Revision: 1.10 $ Initialized net_namespace: 152 bytes NET: Registered protocol family 16 PCI: Probing PCI hardware SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 16384 (order: 4, 65536 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered hwrtype_roach version CVS-$Revision: 1.1 $ registered JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. io scheduler noop registered (default) Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x0 (irq = 0) is a 16550A serial8250: ttyS1 at MMIO 0x0 (irq = 1) is a 16550A serial8250: ttyS2 at MMIO 0x0 (irq = 35) is a 16550A serial8250: ttyS3 at MMIO 0x0 (irq = 36) is a 16550A brd: module loaded PPC 4xx OCP EMAC driver, version 3.54 mal0: initialized, 2 TX channels, 2 RX channels rgmii0: input 0 in RGMII mode eth0: emac0, MAC 02:44:01:02:05:06 eth0: found Marvell 88E1111 Ethernet PHY (0x01) rgmii0: input 1 in RGMII mode eth1: emac1, MAC 00:00:03:f9:40:ab eth1: found Marvell 88E1111 Ethernet PHY (0x07) tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <[email protected]> Driver 'sd' needs updating - please use bus_type methods physmap platform flash device: 08000000 at f8000000 physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 physmap-flash.0: CFI does not contain boot bank location. Assuming top. number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. RedBoot partition parsing not available Using physmap partition information Creating 5 MTD partitions on "physmap-flash.0": 0x00000000-0x00180000 : "kernel" 0x00180000-0x00400000 : "root" 0x00400000-0x07f60000 : "user" 0x07f60000-0x07fa0000 : "env" 0x07fa0000-0x08000000 : "u-boot" ppc-soc-ohci ppc-soc-ohci.0: USB Host Controller ppc-soc-ohci ppc-soc-ohci.0: new USB bus registered, assigned bus number 1 ppc-soc-ohci ppc-soc-ohci.0: irq 21, io mem 0xe0000400
