Hi Jeffrey, Thanks, this looks spot on.
Kind regards, Adam On Thu, 03 Feb 2022, 12:12 AM 'Kobesky, Jeffrey CIV USN NRL (5555) Washington DC (USA)' via [email protected], < [email protected]> wrote: > Hello Nitika, > > > > I’m not using conda environment so I can’t comment on that, but: > > > > 1. To clear the “Odd?” problem I ssh’d into red pitaya and added > “127.0.0.1 localhost” line to etc/hosts on red pitaya. > > > > 3. To clear the “value seems to also be varying rapidly rather than > incrementing steadily as expected” problem I updated casperfpga from > version 0.1.1 to 0.4.4. This can be done by doing: > > > > ~/casperfpga$ sudo pip install -r requirements > > ~/casperfpga$ sudo pip install . > > > > instead of: > > > > ~/casperfpga$ sudo pip install -r requirements > > ~/casperfpga$ sudo pip install casperfpga > > > > i.e., doing it the first way installs from the local repo instead of the > remote repo which I think contains an outdate version of casperfpga. You > can verify your version is ipython by: > > > > In[x] casperfpga.--version-- (not sure I have the syntax exactly right) > > > > Hope that helps -- Jeff > > > > [image: cid:[email protected]] > > *Jeffrey Kobesky * > > Electronics Engineer > > Naval Research Laboratory > > Information Technology Division Code 5555 > > Bldg 1 Room 222 > > 4555 Overlook Ave SW > > Washington, DC 20375 > > Office 202.404.7109 Mobile 443.243.1554 > > [email protected] > > > > > > *From:* Yadlapalli, Nitika <[email protected]> > *Sent:* Tuesday, January 25, 2022 6:34 PM > *To:* [email protected] > *Subject:* [casper] Red Pitaya programming/clocking issue? > > > > Hi all! > > > > I am getting started with casper on a Red Pitaya 125-14. I've been > following the tutorial about using the ADC/DAC boards ( > https://casper-toolflow.readthedocs.io/projects/tutorials/en/latest/tutorials/redpitaya/tut_adc_dac.html) > and have run into a few issues: > > > > 1. I'm not able to use upload the upload_to_ram_and_program method > with the .fpg file. I get this "ERROR:10.42.0.69:10.42.0.69: no > programming informs yet. Odd?" and I don't seem to be able to > activate the tcpborphserver on the red pitaya either to fix it as I've seen > in a previous archive thread. > 2. > > 3. I can use the .bof file for programming the red pitaya, so I've > been moving forward with that. If I try to get the clock speed, however, > using estimate_fpga_clock(), the output estimated clock speed changes > wildly with time and is never consistent with the 125 MHz speed I expect. > Additionally, if I try to read the adc_samp_cnts register as outlined in > the tutorial, the value seems to also be varying rapidly rather than > incrementing steadily as expected. > > > > Has anyone encountered these issues before? I have all the packages > installed in a conda environment. > > > > > > Best, > > Nitika > > > > Nitika Yadlapalli (she/hers) > > PhD Candidate | Astronomy > > California Institute of Technology > > > > -- > You received this message because you are subscribed to the Google Groups " > [email protected]" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/a/lists.berkeley.edu/d/msgid/casper/BYAPR03MB3752B864ED192276D1253C48DA5F9%40BYAPR03MB3752.namprd03.prod.outlook.com > <https://groups.google.com/a/lists.berkeley.edu/d/msgid/casper/BYAPR03MB3752B864ED192276D1253C48DA5F9%40BYAPR03MB3752.namprd03.prod.outlook.com?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups " > [email protected]" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/a/lists.berkeley.edu/d/msgid/casper/d06885fb859d4869b6d7c058b9234f82%40nrl.navy.mil > <https://groups.google.com/a/lists.berkeley.edu/d/msgid/casper/d06885fb859d4869b6d7c058b9234f82%40nrl.navy.mil?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "[email protected]" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/a/lists.berkeley.edu/d/msgid/casper/CADTJ%3DnGTPneYuc%2BF1UpPFzekm-1V6d807SndKj6TeYr-REvFMA%40mail.gmail.com.
