asa1# sh run all failover
failover
failover lan unit primary
failover lan interface lanfail GigabitEthernet0/0.7
failover polltime unit 1 holdtime 15
failover polltime interface 5 holdtime 25
failover interface-policy 1
failover key *****
failover interface ip lanfail 1.2.3.6 255.255.255.0 standby 1.2.3.7
failover group 1
primary
preempt
polltime interface 5 holdtime 25
interface-policy 2
failover group 2
secondary
preempt
polltime interface 5 holdtime 25
interface-policy 1
asa1#
Failover On
Failover unit Primary
Failover LAN Interface: lanfail GigabitEthernet0/0.7 (up)
Unit Poll frequency 1 seconds, holdtime 15 seconds
Interface Poll frequency 5 seconds, holdtime 25 seconds
Interface Policy 1
Monitored Interfaces 2 of 250 maximum
Version: Ours 8.0(5), Mate 8.0(5)
Group 1 last failover at: 13:02:36 UTC Nov 2 2011
Group 2 last failover at: 03:03:29 UTC Nov 3 2011
This host: Primary
Group 1 State: Active
Active time: 57523 (sec)
Group 2 State: Standby Ready
Active time: 2384 (sec)
slot 0: ASA5520 hw/sw rev (2.0/8.0(5)) status (Up Sys)
admin Interface inside (10.20.30.46): Normal
king Interface outside (20.10.30.47): Normal
slot 1: empty
Other host: Secondary
Group 1 State: Standby Ready
Active time: 6529 (sec)
Group 2 State: Active
Active time: 21722 (sec)
slot 0: ASA5520 hw/sw rev (2.0/8.0(5)) status (Up Sys)
admin Interface inside (10.20.30.67): Normal
king Interface outside (20.10.30.46): Normal
slot 1: empty
Stateful Failover Logical Update Statistics
Link : Unconfigured.
With regards
Kings
On Thu, Nov 3, 2011 at 9:07 AM, FNK <[email protected]> wrote:
> Can u provide sh run all failover. And complete sho failover. Thanks
>
> FNK
> Sent from an iPhone
>
>
> On Nov 2, 2011, at 12:13 PM, Kingsley Charles <[email protected]>
> wrote:
>
> Hi Piotr
>
> That command doesn't show info relating to the intf policy.
>
> With regards
> Kings
>
> On Wed, Nov 2, 2011 at 9:39 PM, Piotr Matusiak <[email protected]> wrote:
>
>> Hi Kings,
>>
>> What about sho failover group 1?
>>
>> Regards,
>> Piotr
>>
>>
>> 2011/11/2 Kingsley Charles <[email protected]>
>>
>>> Hi all
>>>
>>> With A/A failover, the interface policy is configured per group and not
>>> the unit. But "show failover" command doesn't display "interface policy"
>>> for two groups separately. Any thoughts?
>>>
>>>
>>> asa1# sh failover
>>> Failover On
>>> Failover unit Primary
>>> Failover LAN Interface: lanfail GigabitEthernet0/2 (up)
>>> Unit Poll frequency 1 seconds, holdtime 15 seconds
>>> Interface Poll frequency 5 seconds, holdtime 25 seconds
>>> Interface Policy 2
>>> Monitored Interfaces 3 of 250 maximum
>>> Version: Ours 8.0(5), Mate 8.0(5)
>>> Group 1 last failover at: 12:20:01 UTC Nov 2 2011
>>> Group 2 last failover at: 12:20:01 UTC Nov 2 2011
>>>
>>>
>>> With regards
>>> Kings
>>>
>>> _______________________________________________
>>> For more information regarding industry leading CCIE Lab training,
>>> please visit www.ipexpert.com
>>>
>>> Are you a CCNP or CCIE and looking for a job? Check out
>>> www.PlatinumPlacement.com
>>>
>>
>>
> _______________________________________________
> For more information regarding industry leading CCIE Lab training, please
> visit www.ipexpert.com
>
> Are you a CCNP or CCIE and looking for a job? Check out
> www.PlatinumPlacement.com
>
>
_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
Are you a CCNP or CCIE and looking for a job? Check out
www.PlatinumPlacement.com
