OK feedback time.... I tried doing everything which Amy and Angel suggested and still it did not work!
I have this under my telephony now: telephony-service sdspfarm units 2 sdspfarm tag 1 sbconf no privacy conference hardware srst mode auto-provision all srst ephone template 1 srst dn template 1 srst dn line-mode dual-octo max-ephones 5 max-dn 10 preference 5 ip source-address 10.10.201.1 port 2000 max-conferences 8 gain -6 moh music-on-hold.au multicast moh 239.1.1.1 port 16384 route 10.10.110.2 10.10.201.1 transfer-system full-consult secondary-dialtone 9 create cnf-files version-stamp 7960 Jun 07 2010 16:28:17 ephone-1[0] Mac:0017.9402.CF34 TCP socket:[1] activeLine:0 REGISTERED in SCCP ver 17/9 mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 caps:11 privacy:0 IP:192.168.10.15 31806 7961 keepalive 17 max_line 6 button 1: dn 5 number 4001 CH1 IDLE CH2 IDLE CH3 IDLE CH4 IDLE CH5 IDLE CH6 IDLE CH7 IDLE CH8 IDLE button 2: dn 6 number 4021 CH1 IDLE CH2 IDLE CH3 IDLE CH4 IDLE CH5 IDLE CH6 IDLE CH7 IDLE CH8 IDLE shared privacy button is enabled Preferred Codec: g711ulaw ephone-3[2] Mac:0018.195A.B173 TCP socket:[3] activeLine:0 REGISTERED in SCCP ver 17/9 mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 caps:11 privacy:0 IP:192.168.10.13 31052 7961 keepalive 14 max_line 6 button 1: dn 8 number 4003 CH1 IDLE CH2 IDLE CH3 IDLE CH4 IDLE CH5 IDLE CH6 IDLE CH7 IDLE CH8 IDLE button 2: dn 6 number 4021 CH1 IDLE CH2 IDLE CH3 IDLE CH4 IDLE CH5 IDLE CH6 IDLE CH7 IDLE CH8 IDLE shared privacy button is enabled Preferred Codec: g711ulaw the dial-peer hunt 3 has been configured. Privacy button under ephones configured. Now when I press the shared line button to Barge in..I sometimes get a glimpse of Cbarge Newcall Softkey and then within a fraction of a second it disappears with the new call softkey template and I get a dial tone. Router has been rebooted as well. did you give it a go Angel? cv On Mon, Jun 7, 2010 at 10:37 AM, Angel Perez <[email protected]> wrote: > Hi, you are partially right: > > When your phones registered back to ucm the e-phone stay there > but dial-peer generated by cme srst doesn't point to anything (you can > varify this with show dial-peer voice summ). > > But it's true that sometimes (it think that it is a bug) the ephone > dial-peer still points to the dn number so once that your phones register > back to ucm you can have problems with incomming calls > > With mgcp you don't have this problem becouse the gw is totally under ucm > control so an incoming call won't match dial-peers , with h323 gw is > different and ephone dial-peer will be matched, but you can easly change > this behaviour like this: > > *telephony service* > *...* > *srst mode auto all* > *max-dn 10 preference 5* > *...* > *exit* > ** > ** > *dial-peer hunt ?* > * <0-7> Dial-peer hunting choices, listed in hunting order within each > choice: > 0 - Longest match in phone number, explicit preference, random selection. > 1 - Longest match in phone number, explicit preference, least recent use. > 2 - Explicit preference, longest match in phone number, random selection. > 3 - Explicit preference, longest match in phone number, least recent use. > 4 - Least recent use, longest match in phone number, explicit preference. > 5 - Least recent use, explicit preference, longest match in phone number. > 6 - Random selection. > 7 - Least recent use.* > ** > *dial-peer hunt 3* > ** > *dial-peer voice 1000 voip* > *description toUCM* > *destination-pattern 1... * > *preference 1* > *...* > ** > ** > This way when a call enter the gw it will match the preference first > instead longest match and calls will still work in srst mode and out srst > mode. > > Try it and play a littel bit with it, you will find that is not difficult > > ps: also there is another bug with cme srst auto all, if you modify the > auto generated ephones or ephones dn (let say name or label) sometimes when > you go back to ucm and then to srts again the ephone won't take a dn, it > will register to srst but the phone display won't show a line, in this case > reload the router and everithing will start working as expected (this have > been discused on the list) > > As you see cme srst is not pretty stable but with this two trick you can > make it works easly if you have littel experience with it > > hth > > > > > > > > ------------------------------ > Date: Mon, 7 Jun 2010 10:16:47 +0100 > Subject: Re: [OSL | CCIE_Voice] CBarge in SRST ~(Again) > From: [email protected] > > To: [email protected] > CC: [email protected] > > No Angel.. > > I am using srst mode auto-prov none.. > > I was thinking that if I use all then that will create ephone permenantly > so after link comes back up (or primary ccm) then phones will register with > the CUCM while ephones will still stay there...I have not tested this but > this one colleague of mine had inbound calls issue after phones registred > back to CUCM as the call was going to the ehpones instead of taking the voip > dial-peer. Have you tested this? > > vc > > On Mon, Jun 7, 2010 at 10:00 AM, ccie voice <[email protected]> wrote: > > Thanks Angel. > > I am at work but will give it a go today. > > I am just wondering that everytime when phones will go in SRST..do I have > to go into ephones and add the button? this does not look practical. > > I will give it a go anyways. > > vc > > > On Mon, Jun 7, 2010 at 9:39 AM, Angel Perez <[email protected]> wrote: > > Hi: > > Once the ephones have registered to srst add privacy button under ephone. > > Let us know, hth > > ------------------------------ > Date: Sun, 6 Jun 2010 21:46:26 +0100 > From: [email protected] > > To: [email protected] > Subject: [OSL | CCIE_Voice] CBarge in SRST ~(Again) > > Hi, > > Sorry for the incomplete email earlier. > Has anyone tried cBarge in SRST mode? I have my conference bridge > registered to telephony service when it goes into SRST. I have used priority > 3 as the telephony-service address. When my phones go in SRST mode, I can > see they have shared line and when I am making a call on this shared line, I > can see both phones ringing. > However, if i receive call at one phone and try to Barge in using another > all I get is a dialtone..no Cbarge softkey or anything even thou Cbarge key > is configured under ephone template. Also privacy is off at telephony > service. I even went into ephones and turned the privacy off but it is still > not working. For some reason its not bringing the remote-in-use softkey > template. I am getting a new call softkey template. > > > R2#sh ephone > > ephone-1[0] Mac:0017.9402.CF34 TCP socket:[1] activeLine:0 REGISTERED in > SCCP ver 17/9 > mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 > caps:11 privacy:0 > IP:192.168.10.22 33399 7961 keepalive 0 max_line 6 > button 1: dn 5 number 4001 CM Fallback CH1 IDLE CH2 > IDLE CH3 IDLE CH4 IDLE CH5 IDLE CH6 > IDLE CH7 IDLE CH8 IDLE > button 2: dn 6 number 4021 CM Fallback CH1 IDLE CH2 > IDLE CH3 IDLE CH4 IDLE CH5 IDLE CH6 > IDLE CH7 IDLE CH8 IDLE * shared* > Preferred Codec: g711ulaw > > > ephone-2[1] Mac:0030.94C3.EE93 TCP socket:[3] activeLine:0 REGISTERED in > SCCP ver 11/9 > mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 > caps:8 privacy:0 > IP:192.168.10.17 52129 Telecaster 7960 keepalive 3 max_line 6 > button 1: dn 7 number 4002 CM Fallback CH1 IDLE CH2 > IDLE CH3 IDLE CH4 IDLE CH5 IDLE CH6 > IDLE CH7 IDLE CH8 IDLE > button 2: dn 6 number 4021 CM Fallback CH1 IDLE CH2 > IDLE CH3 IDLE CH4 IDLE CH5 IDLE CH6 > IDLE CH7 IDLE CH8 IDLE shared > Preferred Codec: g711ulaw > > Adios > > ------------------------------ > Hotmail: Free, trusted and rich email service. Get it now. > > > > > ------------------------------ > Your E-mail and More On-the-Go. Get Windows Live Hotmail Free. Sign up > now. <https://signup.live.com/signup.aspx?id=60969> >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
