Hi cv:
I didn't have time yesterday,sorry I'll try asap
thx
Date: Mon, 7 Jun 2010 23:07:57 +0100
Subject: Re: [OSL | CCIE_Voice] CBarge in SRST ~(Again)
From: [email protected]
To: [email protected]; [email protected]
CC: [email protected]
OK feedback time....
I tried doing everything which Amy and Angel suggested and still it did not
work!
I have this under my telephony now:
telephony-service
sdspfarm units 2
sdspfarm tag 1 sbconf
no privacy
conference hardware
srst mode auto-provision all
srst ephone template 1
srst dn template 1
srst dn line-mode dual-octo
max-ephones 5
max-dn 10 preference 5
ip source-address 10.10.201.1 port 2000
max-conferences 8 gain -6
moh music-on-hold.au
multicast moh 239.1.1.1 port 16384 route 10.10.110.2 10.10.201.1
transfer-system full-consult
secondary-dialtone 9
create cnf-files version-stamp 7960 Jun 07 2010 16:28:17
ephone-1[0] Mac:0017.9402.CF34 TCP socket:[1] activeLine:0 REGISTERED in SCCP
ver 17/9
mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 caps:11
privacy:0
IP:192.168.10.15 31806 7961 keepalive 17 max_line 6
button 1: dn 5 number 4001 CH1 IDLE CH2 IDLE CH3 IDLE
CH4 IDLE CH5 IDLE CH6 IDLE CH7 IDLE
CH8 IDLE
button 2: dn 6 number 4021 CH1 IDLE CH2 IDLE CH3 IDLE
CH4 IDLE CH5 IDLE CH6 IDLE CH7 IDLE
CH8 IDLE shared
privacy button is enabled
Preferred Codec: g711ulaw
ephone-3[2] Mac:0018.195A.B173 TCP socket:[3] activeLine:0 REGISTERED in SCCP
ver 17/9
mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 caps:11
privacy:0
IP:192.168.10.13 31052 7961 keepalive 14 max_line 6
button 1: dn 8 number 4003 CH1 IDLE CH2 IDLE CH3 IDLE
CH4 IDLE CH5 IDLE CH6 IDLE CH7 IDLE
CH8 IDLE
button 2: dn 6 number 4021 CH1 IDLE CH2 IDLE CH3 IDLE
CH4 IDLE CH5 IDLE CH6 IDLE CH7 IDLE
CH8 IDLE shared
privacy button is enabled
Preferred Codec: g711ulaw
the dial-peer hunt 3 has been configured.
Privacy button under ephones configured.
Now when I press the shared line button to Barge in..I sometimes get a glimpse
of Cbarge Newcall Softkey and then within a fraction of a second it disappears
with the new call softkey template and I get a dial tone.
Router has been rebooted as well.
did you give it a go Angel?
cv
On Mon, Jun 7, 2010 at 10:37 AM, Angel Perez <[email protected]> wrote:
Hi, you are partially right:
When your phones registered back to ucm the e-phone stay there but dial-peer
generated by cme srst doesn't point to anything (you can varify this with show
dial-peer voice summ).
But it's true that sometimes (it think that it is a bug) the ephone dial-peer
still points to the dn number so once that your phones register back to ucm you
can have problems with incomming calls
With mgcp you don't have this problem becouse the gw is totally under ucm
control so an incoming call won't match dial-peers , with h323 gw is different
and ephone dial-peer will be matched, but you can easly change this behaviour
like this:
telephony service
...
srst mode auto all
max-dn 10 preference 5
...
exit
dial-peer hunt ?
<0-7> Dial-peer hunting choices, listed in hunting order within each choice:
0 - Longest match in phone number, explicit preference, random selection.
1 - Longest match in phone number, explicit preference, least recent use.
2 - Explicit preference, longest match in phone number, random selection.
3 - Explicit preference, longest match in phone number, least recent use.
4 - Least recent use, longest match in phone number, explicit preference.
5 - Least recent use, explicit preference, longest match in phone number.
6 - Random selection.
7 - Least recent use.
dial-peer hunt 3
dial-peer voice 1000 voip
description toUCM
destination-pattern 1...
preference 1
...
This way when a call enter the gw it will match the preference first instead
longest match and calls will still work in srst mode and out srst mode.
Try it and play a littel bit with it, you will find that is not difficult
ps: also there is another bug with cme srst auto all, if you modify the auto
generated ephones or ephones dn (let say name or label) sometimes when you go
back to ucm and then to srts again the ephone won't take a dn, it will register
to srst but the phone display won't show a line, in this case reload the router
and everithing will start working as expected (this have been discused on the
list)
As you see cme srst is not pretty stable but with this two trick you can make
it works easly if you have littel experience with it
hth
Date: Mon, 7 Jun 2010 10:16:47 +0100
Subject: Re: [OSL | CCIE_Voice] CBarge in SRST ~(Again)
From: [email protected]
To: [email protected]
CC: [email protected]
No Angel..
I am using srst mode auto-prov none..
I was thinking that if I use all then that will create ephone permenantly so
after link comes back up (or primary ccm) then phones will register with the
CUCM while ephones will still stay there...I have not tested this but this one
colleague of mine had inbound calls issue after phones registred back to CUCM
as the call was going to the ehpones instead of taking the voip dial-peer. Have
you tested this?
vc
On Mon, Jun 7, 2010 at 10:00 AM, ccie voice <[email protected]> wrote:
Thanks Angel.
I am at work but will give it a go today.
I am just wondering that everytime when phones will go in SRST..do I have to go
into ephones and add the button? this does not look practical.
I will give it a go anyways.
vc
On Mon, Jun 7, 2010 at 9:39 AM, Angel Perez <[email protected]> wrote:
Hi:
Once the ephones have registered to srst add privacy button under ephone.
Let us know, hth
Date: Sun, 6 Jun 2010 21:46:26 +0100
From: [email protected]
To: [email protected]
Subject: [OSL | CCIE_Voice] CBarge in SRST ~(Again)
Hi,
Sorry for the incomplete email earlier.
Has anyone tried cBarge in SRST mode? I have my conference bridge registered to
telephony service when it goes into SRST. I have used priority 3 as the
telephony-service address. When my phones go in SRST mode, I can see they have
shared line and when I am making a call on this shared line, I can see both
phones ringing.
However, if i receive call at one phone and try to Barge in using another all I
get is a dialtone..no Cbarge softkey or anything even thou Cbarge key is
configured under ephone template. Also privacy is off at telephony service. I
even went into ephones and turned the privacy off but it is still not working.
For some reason its not bringing the remote-in-use softkey template. I am
getting a new call softkey template.
R2#sh ephone
ephone-1[0] Mac:0017.9402.CF34 TCP socket:[1] activeLine:0 REGISTERED in SCCP
ver 17/9
mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 caps:11
privacy:0
IP:192.168.10.22 33399 7961 keepalive 0 max_line 6
button 1: dn 5 number 4001 CM Fallback CH1 IDLE CH2 IDLE
CH3 IDLE CH4 IDLE CH5 IDLE CH6 IDLE CH7
IDLE CH8 IDLE
button 2: dn 6 number 4021 CM Fallback CH1 IDLE CH2 IDLE
CH3 IDLE CH4 IDLE CH5 IDLE CH6 IDLE CH7
IDLE CH8 IDLE shared
Preferred Codec: g711ulaw
ephone-2[1] Mac:0030.94C3.EE93 TCP socket:[3] activeLine:0 REGISTERED in SCCP
ver 11/9
mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 caps:8
privacy:0
IP:192.168.10.17 52129 Telecaster 7960 keepalive 3 max_line 6
button 1: dn 7 number 4002 CM Fallback CH1 IDLE CH2 IDLE
CH3 IDLE CH4 IDLE CH5 IDLE CH6 IDLE CH7
IDLE CH8 IDLE
button 2: dn 6 number 4021 CM Fallback CH1 IDLE CH2 IDLE
CH3 IDLE CH4 IDLE CH5 IDLE CH6 IDLE CH7
IDLE CH8 IDLE shared
Preferred Codec: g711ulaw
Adios
Hotmail: Free, trusted and rich email service. Get it now.
Your E-mail and More On-the-Go. Get Windows Live Hotmail Free. Sign up now.
_________________________________________________________________
Your E-mail and More On-the-Go. Get Windows Live Hotmail Free.
https://signup.live.com/signup.aspx?id=60969_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
