Good find! This also confirms one thing about HREAP/FlexConnect APs - the native VLAN specified on the AP config doesn't really matter, other than to specify what is untagged coming from the AP to the switch. The switch was sending tagged VLAN 113 frames to the AP, which would not see the "113" and go "hey, that's my native VLAN, let's use it for management."
Jason Boyers, CCIE #26024 (Wireless) Blog: netboyers.wordpress.com On Mon, Jun 25, 2012 at 1:28 PM, Kristján Ólafur Eðvarðsson < [email protected]> wrote: > Guys I have found the problem.**** > > ** ** > > no vlan dot1q tag native**** > > it was configured on my switch before !**** > > so the AP wants to send untagged packets on vlan113**** > > but the switch tags native vlan packets so this way the communication > doesn´t work.**** > > ** ** > > it was a tricky one :D**** > > ** ** > > regards. Kristjan**** > > ** ** > > *From:* Jason Boyers [mailto:[email protected]] > *Sent:* 25. júní 2012 16:18 > *To:* Victor Platov (viplatov) > *Cc:* Ron Marosko; Kristján Ólafur Eðvarðsson; > [email protected] > > *Subject:* Re: [OSL | CCIE_Wireless] 1242 capwap with poe module and > switchport in vlan trunk mode**** > > ** ** > > True. Victor, that when connected to the power injector, he wouldn't be > able to check the WLC config. However, it appears to be working when in > access mode, so he can connect that way, then check the WLC config, > > The other show commands would be helpful as well. > > Jason Boyers, CCIE #26024 (Wireless) > Blog: netboyers.wordpress.com > > **** > > On Mon, Jun 25, 2012 at 11:52 AM, Victor Platov (viplatov) < > [email protected]> wrote:**** > > I’ve seen that due to power injector misconfiguration AP doesn’t bring up > its radio interfaces but not being stuck. Moreover, It had being connected > to the WLC before, hence I think it’s not the issue.**** > > If the switch isn’t showing the AP’s MAC I suppose CAPWAP tunnel is > down…so I’m afraid Kristján could not check it through WLC.**** > > **** > > Kristján,**** > > **** > > What are the outputs of the following commands from the switch:**** > > Show cdp neighb**** > > Sh run intf …**** > > Sh int ….**** > > Sh intf …. Switchport**** > > Sh intf … trunk**** > > Sh vlan**** > > **** > > *From:* [email protected] [mailto: > [email protected]] *On Behalf Of *Jason Boyers > *Sent:* Monday, June 25, 2012 6:59 PM > *To:* Ron Marosko > *Cc:* Kristján Ólafur Eðvarðsson; [email protected] > *Subject:* Re: [OSL | CCIE_Wireless] 1242 capwap with poe module and > switchport in vlan trunk mode**** > > **** > > What does "show cdp neighbor" show from the console of the AP when > connected in the fashion you are describing? This may also be an issue in > terms of the WLC config of the AP. What do you have for the "Power > Injector State" and "Power Injector Selection" under the AP config Advanced > tab? > > Jason Boyers, CCIE #26024 (Wireless) > Blog: netboyers.wordpress.com**** > > On Mon, Jun 25, 2012 at 9:31 AM, Ron Marosko <[email protected]> wrote:*** > * > > Make sure you define "switchport trunk native vlan x" to define the vlan > upon which untagged packets should reside. By default, this will be vlan 1, > and if you are using a different vlan id in your access vlan command, then > that would be why the mac address isn't showing up in the expected vlan. > The access point in default or unconfigured mode has no idea about any > vlan tags, and thus is always sending untagged packets. Only when you > configure the access point in HREAP mode will it start to even attempt to > use 802.1q tags, if appropriately configured. > > Regards, > Ron > > -- > Ron Marosko, Jr. > . . . . . . . . . . . . . . . . . . . . . . . . . . > CCIE No. 4526 (R/S), CWNA, ACMA, NN5DX > Consulting Network Architect > Global Technology Resources,Inc. > 1108 West Dickinson Blvd, Suite A > Fort Stockton, TX 79735 USA > o: +1 432 336 5600 x110 > c: +1 720 233 3147 > e: [email protected] > pgp pubkey: 0x58AB8B5C > "To know me is to fly with me."**** > > > > > -----Original Message----- > From: [email protected] [mailto: > [email protected]] On Behalf Of Kristján Ólafur > Eðvarðsson > Sent: Monday, June 25, 2012 8:16 AM > To: [email protected] > Subject: [OSL | CCIE_Wireless] 1242 capwap with poe module and switchport > in vlan trunk mode > > I have been troubleshooting a capwap ap connectivity. > The ap is 1242 with poe injector (if it is relevant) and works fine on a > access vlan. > Now puting the port to trunk mode (native vlan correct and the same as it > was on access) However when I change to trunk mode the AP Mac address > disapears from the interface mac table and I cant communicate get an DHCP > or whatever. > > Has anyone seen something like that ? > > I tried clear capwap private config, > reload the switch, > shut un shut ports. > > Still the MAC address just isn´t learned and this is the core of the > problem. Its a 3560 switch. > As soon as I change to access mode the mac is learned instantly. > > I have never seen this issue before, wonder if someone knows anything. > > regards. Kristjan > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com**** > > This message contains confidential information and is intended only for > the individual named. Please notify the sender immediately by e-mail if you > have received this e-mail by mistake and delete this e-mail from your > system. Any opinions presented in this email are solely those of the author > and do not necessarily represent those of the company. E-mail transmission > cannot be guaranteed to be secure or error-free; the sender therefore does > not accept liability for any errors or omissions in the contents of this > message, which arise as a result of e-mail transmission.**** > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com**** > > **** > > ** ** >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
