The parent should never be a BVI - only radios can be parents. Also, have you tried to associate without using encryption and without the mac-list on the 1142? That is always the first step - get the association to work, then add security to that. Otherwise, you run into the issue of not knowing what is causing the problem - the wireless component or the security component. Also, your configuration doesn't show how the 1121 is actually sending credentials to the 1142. That needs to be configured, and the configuration will depend on the EAP type used.
Jason Boyers, CCIE #26024 (Wireless) Blog: netboyers.wordpress.com On Mon, Nov 19, 2012 at 9:19 AM, Kumar Gollapudi <[email protected]>wrote: > Hi, > > There is a challenge in configuring Cisco Access Point 1121 into Repeater > Mode with Root Station AP 1142. The Root station has two Radio's 0 & 1 (2.4 > Ghz & 5.Ghz). We configurfed to associate the Cisco AP 1121 on both Radio > Stations & BVI1. But its trying to assoicate with 1142 with lot of error's. > > '%DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Not > specified parent > > %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: No Response > > %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Rcvd > response from > > Actually the Root Stations has been configured with MAC & AD based > authenticatoin to associate the client devices(laptops). Looking for your > valuable suggestions on the issue. > > > > > > *On Root Station: (Standalone Cisco 1142 Access Point)* > > > > dot11 ssid AC-CORP-WIFI-IND > > authentication open eap eap_methods1 > > authentication network-eap eap_methods1 > > authentication key-management wpa > > > > interface Dot11Radio0 > > no ip address > > no ip route-cache > > ! > > encryption mode ciphers aes-ccm > > ! > > ssid XXXXXXX > > ! > > speed basic-1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0 > > station-role root > > dot1x reauth-period 3 > > bridge-group 1 > > bridge-group 1 subscriber-loop-control > > bridge-group 1 block-unknown-source > > no bridge-group 1 source-learning > > no bridge-group 1 unicast-flooding > > bridge-group 1 spanning-disabled > > > > dot11 association mac-list xxxx > > ip radius source-interface BVI1 > > > > > > *On Repeater Device: (Cisco Access 1121) > * > > > > dot11 ssid XXXXXXXXXX > > authentication open eap eap_methods1 > > authentication network-eap eap_methods1 > > authentication key-management wpa > > infrastructure-ssid optional > > > > > > > > > > interface Dot11Radio0 > > no ip address > > no ip route-cache > > ! > > encryption mode ciphers aes-ccm > > ! > > ssid AC-CORP-WIFI-IND > > ! > > speed basic-1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0 > > station-role repeater > > dot1x reauth-period 3 > > parent 1 xxxx.xxxx.xxxx (BVI1) > > parent 2 xxxx.xxxx.xxxx (Dot11Radio0) > > parent 3 xxxx.xxxx.xxxx (Dot11Radio1) > > bridge-group 1 > > bridge-group 1 subscriber-loop-control > > bridge-group 1 block-unknown-source > > no bridge-group 1 source-learning > > no bridge-group 1 unicast-flooding > > bridge-group 1 spanning-disabled > Thanks > Kumar G > > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com > >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
