Hi,
I jst tried out this below
<project name="NGFMS" queue="Q1" queuePriority="1">
But i dont see any change as it is invoking another IDE when the 1st IDE is
doing the building proccess.
with kind regards
Maddy
On Mon, Apr 6, 2009 at 12:30 PM, Ruben Willems <[email protected]>wrote:
> Hi
>
>
> what you can try is the following :
> specify a queue name and priority on the project
> see
>
> http://confluence.public.thoughtworks.org/display/CCNET/Project+Configuration+Block
>
>
> maybe that resolves the problem
> so the bug only manifests itself with a minimal project setup.
>
>
> with kind regards
> Ruben Willems
>
>
>
> On Mon, Apr 6, 2009 at 8:56 AM, madhu nambiar
> <[email protected]>wrote:
>
>> Thanks ruben,I had pasted the ccnet.config initial part below
>>
>> <cruisecontrol>
>> <project name="VSAT">
>> <sourcecontrol type="filtered">
>> <sourceControlProvider type="filesystem">
>> <repositoryRoot>C:\MyProj</repositoryRoot>
>> <autoGetSource>true</autoGetSource>
>> <ignoreMissingRoot>false</ignoreMissingRoot>
>> </sourceControlProvider>
>> Do we need to specify anything else for the queinng integration to work???
>>
>> with kind regards
>> Maddy
>> On Mon, Apr 6, 2009 at 12:21 PM, Ruben Willems <[email protected]
>> > wrote:
>>
>>> Hi
>>>
>>>
>>> than this is a bug :-(
>>> Made a bug report :
>>> http://jira.public.thoughtworks.org/browse/CCNET-1449
>>>
>>> let's see what we can do to solve it
>>>
>>>
>>> with kind regards
>>> Ruben Willems
>>>
>>>
>>> On Mon, Apr 6, 2009 at 8:44 AM, madhu nambiar <[email protected]
>>> > wrote:
>>>
>>>> Hi,
>>>> Cruise Control.NET 1.4.3.
>>>>
>>>>
>>>> with regards
>>>> Maddy
>>>>
>>>> On Mon, Apr 6, 2009 at 12:04 PM, Ruben Willems <
>>>> [email protected]> wrote:
>>>>
>>>>> Hi
>>>>>
>>>>> which version of CCNet are you using ?
>>>>>
>>>>> with kind regards
>>>>> Ruben Willems
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> On Mon, Apr 6, 2009 at 7:31 AM, Maddy <[email protected]> wrote:
>>>>>
>>>>>>
>>>>>> Hi ,
>>>>>> This is a doubt regarding the material published in the
>>>>>> following link
>>>>>> "http://confluence.public.thoughtworks.org/display/CCNET/Integration
>>>>>> +Queues"
>>>>>>
>>>>>>
>>>>>> which tells that "The default behaviour of CruiseControl.Net is that
>>>>>> each project defined in the configuration is given its own integration
>>>>>> thread, thereby allowing differently named projects to build
>>>>>> concurrently.
>>>>>>
>>>>>> Note however that a single project can never be building more than
>>>>>> once at the same time. If you force a build on Project X while it is
>>>>>> already integrating, that force build request is effectively blocked
>>>>>> until the previous integration completes. So you can also think of
>>>>>> this as each project having its own dedicated integration queue, where
>>>>>> only the item at the head of the queue can be currently building, with
>>>>>> at most one request pending."
>>>>>>
>>>>>> But this is really contradicting in my case as when i force my build
>>>>>> it opens my IDE and starts the integration and building which takes
>>>>>> about 3 min approx. but when i force my build in between the execution
>>>>>> on my webdash board i see that it again opens another IDE and starts
>>>>>> the building which is not acceptable.According to the link shown
>>>>>> above,it should queue and wait for the 1st IDE execution to complete
>>>>>> and then go for the 2nd one.
>>>>>>
>>>>>>
>>>>>> Can u plz suggest any solution to this problem??
>>>>>>
>>>>>> with kind regards
>>>>>> Maddy
>>>>>>
>>>>>
>>>>>
>>>>
>>>
>>
>
