Hello Hal:
Thanks for the Copy of Joerg's message.
How is this logic?
TAO works on Win98 w/adaptec's create CD software therefore it should work
using the self-same hardware IF the Linux Software was not broken SOME WHERE.
The source of the software fault has not been owned up to as far as I can determine.
Regards,
John Turner
8/16/01 7:47:47 PM, "Hal Purdy" <[EMAIL PROTECTED]> wrote:
>Joerg,
>Thanks much for the quick reply. Should I assume that the firmware bug in
>Goldstar drives is also a bug in HP CD-RW drives?
>
>I did notice that while the HP 9500 was listed as a supported drive on your
>cdrecord website, your inquiry string had a firmware revision of 1.6 while
>my firmware is at 1.4. To your knowledge, would upgrading to 1.6 help?
>
>I did search perfunctorily for HP CD-RW drive firmware upgrades but found
>nothing. Since you're working on a UNIX firmware upgrade tool, perhaps you
>(or someone else on the list) know where I could find HP firmware upgrades
>for their CD-RW products.
>
>Alas, cdrecord is embedded in an application we use and that application is
>currently setup to use cdrecord in TAO mode. While I could perhaps cajole
>the developers to change the application to optionally work in DAO mode, it
>would be far easier for me to get an ATAPI drive that works in TAO mode.
>
>Thanks again,
>Hal
>
>> -----Original Message-----
>> From: Joerg Schilling [mailto:[EMAIL PROTECTED]]
>> Sent: Thursday, August 16, 2001 6:53 PM
>> To: [EMAIL PROTECTED]; [EMAIL PROTECTED]
>> Subject: Re: HP 9500b ATAPI - "illegal mode for this track" error
>>
>>
>>
>> >From: "Hal Purdy" <[EMAIL PROTECTED]>
>>
>> >I am experiencing problems using cdrecord to do audio TAO burns with a HP
>> >9500b ATAPI CD-RW.
>> >Cdrecord DAO data burns work fine as do DAO audio burns using cdrdao.
>>
>> >I am running a 2.4.2-2 Linux kernel with libc.2.2.2.so (libc.so.6) (stock
>> >RedHat 7.1).
>> >The processor is a Pentium III running at 866 Mhz.
>> >I first experienced this problem with cdrtools-1.9 and then
>> cdrtools-1.11a1.
>> >Then,
>> >I built cdrtools-1.11a06 and used the following command line:
>> >$ usr/local/src/cdrtools-1.11/cdrecord/OBJ/i686-linux-cc/cdrecord -v -dev
>> >1,1,0 -audio /share/music/pcm/Rock/*/*/03*.pcm >cdrecord.out 2>&1
>>
>> >It generated the output given below.
>> >In searching the web, I find that other people have experienced
>> similar if
>> >not identical problems including one reported to this list:
>>
>> >From: John L. Turner
>> >Subject: Re: RE:ide-scsi problem!
>> >Date: Fri, 01 Jun 2001 13:30:02 -0700
>>
>> >However, I have not seen any workaround or solution anywhere. I
>> have tried a
>> >couple of things which are briefly described after the cdrecord output
>> >below.
>>
>> >Any help or advice would be greatly appreciated.
>>
>> >scsidev: '1,1,0'
>> >scsibus: 1 target: 1 lun: 0
>> >Linux sg driver version: 3.1.17
>> >Cdrecord 1.11a05 (i686-pc-linux-gnu) Copyright (C) 1995-2001
>> J�rg Schilling
>> >TOC Type: 0 = CD-DA
>> >Using libscg version 'schily-0.5'
>> >atapi: 1
>> >Device type : Removable CD-ROM
>> >Version : 0
>> >Response Format: 1
>> >Vendor_info : 'HP '
>> >Identifikation : 'CD-Writer+ 9500b'
>> >Revision : '1.04'
>> >Device seems to be: Generic mmc CD-RW.
>> >Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
>> >Driver flags : SWABAUDIO
>> >Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16
>> RAW/R96P RAW/R96R
>> >Drive buf size : 5185536 = 5064 KB
>> >FIFO size : 4194304 = 4096 KB
>> >Track 01: audio 45 MB (04:32.44) no preemp swab
>> ....
>>
>> >Track 01: 0 of 45 MB
>> >written./usr/local/src/cdrtools-1.11/cdrecord/OBJ/i686-linux-cc/cdrecord:
>> >Input/output error. write_g1: scsi sendcmd: no error
>> >CDB: 2A 00 00 00 00 00 00 00 1B 00
>> >status: 0x2 (CHECK CONDITION)
>> >Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 64 00 00 00
>> >Sense Key: 0x5 Illegal Request, Segment 0
>> >Sense Code: 0x64 Qual 0x00 (illegal mode for this track) Fru 0x0
>> >Sense flags: Blk 0 (not valid)
>> >cmd finished after 0.002s timeout 40s
>> >Sense Bytes: 70 00 00 00 00 00 00 0A 00 00 00 00 00 00 00 00 00 00
>>
>> This is caused by a firmware bug of the Goldstar drive. Use DAO
>> mode this has been
>> tested to work.
>>
>> J�rg
>>
>> EMail:[EMAIL PROTECTED] (home) J�rg Schilling
>> D-13353 Berlin
>> [EMAIL PROTECTED] (uni) If you don't have iso-8859-1
>> [EMAIL PROTECTED] (work) chars I am J"org Schilling
>> URL: http://www.fokus.gmd.de/usr/schilling
>ftp://ftp.fokus.gmd.de/pub/unix
>
>
>
>
John Turner
2425 Poca River Rd. South
Poca, WV 25159-9027
voice 304 776-3675
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
