Hello,
I cannot find the solution for the problem i'm having.
When I'm burning CD-rewritable's all is going well.
But when i'm burning CD-recordable's I get an error when
cdrecord is fixating the CD.
Can somebody look at the information below and give me a tip
where to look for the solution ?
Hardware :
- Adaptec AHA-2940A Ultra SCSI Host Adapter.
- Philips CDD3600 CD-R/RW Rev: 2.00
The information from CD-record :
[kees@chocomel]# sudo cdrecord -dummy enigma-docs.iso
Cdrecord 1.10 (i686-pc-linux-gnu) Copyright (C) 1995-2001 J�rg Schilling
scsidev: '0,4,0'
scsibus: 0 target: 4 lun: 0
Linux sg driver version: 3.1.20
Using libscg version 'schily-0.5'
Device type : Removable CD-ROM
Version : 2
Response Format: 2
Capabilities : SYNC
Vendor_info : 'PHILIPS '
Identifikation : 'CDD3600 CD-R/RW '
Revision : '2.00'
Device seems to be: Generic mmc CD-RW.
Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
Driver flags : SWABAUDIO
cdrecord: Input/output error. test unit ready: scsi sendcmd: no error
CDB: 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: F0 00 02 00 00 00 00 28 00 00 6A 72 3A 00 00 00
Sense Key: 0x2 Not Ready, Segment 0
Sense Code: 0x3A Qual 0x00 (medium not present) Fru 0x0
Sense flags: Blk 0 (valid)
cmd finished after 0.009s timeout 40s
cdrecord: No disk / Wrong disk!
[kees@chocomel]# sudo cdrecord enigma-docs.iso
Cdrecord 1.10 (i686-pc-linux-gnu) Copyright (C) 1995-2001 J�rg Schilling
scsidev: '0,4,0'
scsibus: 0 target: 4 lun: 0
Linux sg driver version: 3.1.20
Using libscg version 'schily-0.5'
Device type : Removable CD-ROM
Version : 2
Response Format: 2
Capabilities : SYNC
Vendor_info : 'PHILIPS '
Identifikation : 'CDD3600 CD-R/RW '
Revision : '2.00'
Device seems to be: Generic mmc CD-RW.
Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
Driver flags : SWABAUDIO
Starting to write CD/DVD at speed 2 in write mode for single session.
Last chance to quit, starting real write in 0 seconds. Operation starts.
Track 01: Total bytes read/written: 624476160/624476160 (304920 sectors).
cdrecord: Input/output error. close track/session: scsi sendcmd: no
errorCDB: 5B 00 02 00 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: F0 00 05 00 00 00 00 28 00 07 2A 24 2C 04 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x2C Qual 0x04 (current program area is empty) Fru 0x0
Sense flags: Blk 0 (valid)
cmd finished after 0.018s timeout 480s
cmd finished after 0.018s timeout 480s
The scsi devices are :
[kees@chocomel]# cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 04 Lun: 00
Vendor: PHILIPS Model: CDD3600 CD-R/RW Rev: 2.00
Type: CD-ROM ANSI SCSI revision: 02
Information on the Adaptec :
[kees@chocomel]# cat /proc/scsi/aic7xxx/0
Adaptec AIC7xxx driver version: 5.2.4/5.2.0
Compile Options:
TCQ Enabled By Default : Enabled
AIC7XXX_PROC_STATS : Enabled
Adapter Configuration:
SCSI Adapter: Adaptec AHA-2940A Ultra SCSI host adapter
Ultra Narrow Controller at PCI 0/11/0
PCI MMAPed I/O Base: 0xe9800000
Adapter SEEPROM Config: SEEPROM found and used.
Adaptec SCSI BIOS: Enabled
IRQ: 10
SCBs: Active 0, Max Active 1,
Allocated 31, HW 3, Page 255
Interrupts: 24115
BIOS Control Word: 0x10b6
Adapter Control Word: 0x005c
Extended Translation: Enabled
Disconnect Enable Flags: 0x00ff
Ultra Enable Flags: 0x0000
Tag Queue Enable Flags: 0x0000
Ordered Queue Tag Flags: 0x0000
Default Tag Queue Depth: 32
Tagged Queue By Device array for aic7xxx host instance 0:
{0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0}
Actual queue depth per device for aic7xxx host instance 0:
{1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1}
Statistics:
(scsi0:0:4:0)
Device using Narrow/Sync transfers at 10.0 MByte/sec, offset 15
Transinfo settings: current(25/15/0/0), goal(25/15/0/0), user(25/15/0/0)
Total transfers 9837 (9837 reads and 0 writes)
< 2K 2K+ 4K+ 8K+ 16K+ 32K+ 64K+ 128K+
Reads: 0 0 0 1 0 9836 0 0
Writes: 0 0 0 0 0 0 0 0
I hope somebody can help me with this one.
Thanks,
Kees Kuip
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
