Hello,
Your drive is dying...
I know it is late to answer, but in case it helps you... I started to experiment the
same problem as yours, also with a Philips SCSI CD-RW 3600 model.
For two years it worked well, then started to be only able to write CDRW and
no more CDR failing with the same fixating error. I fixed many times the drive's
hardware (open it, clean, grease, etc...) but the fix only works for
a little time (6 month, then 3, then 1, then a few days, then not at all).
I ended being able to open the computer, remove the drive, open the drive in
less than 5 minutes :-/
I buy a new drive (Yamaha CRW2200SX) and without any software change,
all writings are now perfects.
My diagnostic of the root cause of the problem is the way PCs are designed,
all the air cooling the power supply comming through the CDRW drive and thus
adding dust in the mechanism of the drive. I now have an external drive without
any fan, and I only turn it on when I need to write, reducing the dust and on/off
related problems.
Regards,
JLS
"Mr. Cube" wrote:
> Hello,
>
> I cannot find the solution for the problem i'm having.
>
> When I'm burning CD-rewritable's all is going well.
> But when i'm burning CD-recordable's I get an error when
> cdrecord is fixating the CD.
>
> Can somebody look at the information below and give me a tip
> where to look for the solution ?
>
> Hardware :
> - Adaptec AHA-2940A Ultra SCSI Host Adapter.
> - Philips CDD3600 CD-R/RW Rev: 2.00
>
> The information from CD-record :
>
> [kees@chocomel]# sudo cdrecord -dummy enigma-docs.iso
> Cdrecord 1.10 (i686-pc-linux-gnu) Copyright (C) 1995-2001 J�rg Schilling
> scsidev: '0,4,0'
> scsibus: 0 target: 4 lun: 0
> Linux sg driver version: 3.1.20
> Using libscg version 'schily-0.5'
> Device type : Removable CD-ROM
> Version : 2
> Response Format: 2
> Capabilities : SYNC
> Vendor_info : 'PHILIPS '
> Identifikation : 'CDD3600 CD-R/RW '
> Revision : '2.00'
> Device seems to be: Generic mmc CD-RW.
> Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
> Driver flags : SWABAUDIO
> cdrecord: Input/output error. test unit ready: scsi sendcmd: no error
> CDB: 00 00 00 00 00 00
> status: 0x2 (CHECK CONDITION)
> Sense Bytes: F0 00 02 00 00 00 00 28 00 00 6A 72 3A 00 00 00
> Sense Key: 0x2 Not Ready, Segment 0
> Sense Code: 0x3A Qual 0x00 (medium not present) Fru 0x0
> Sense flags: Blk 0 (valid)
> cmd finished after 0.009s timeout 40s
> cdrecord: No disk / Wrong disk!
> [kees@chocomel]# sudo cdrecord enigma-docs.iso
> Cdrecord 1.10 (i686-pc-linux-gnu) Copyright (C) 1995-2001 J�rg Schilling
> scsidev: '0,4,0'
> scsibus: 0 target: 4 lun: 0
> Linux sg driver version: 3.1.20
> Using libscg version 'schily-0.5'
> Device type : Removable CD-ROM
> Version : 2
> Response Format: 2
> Capabilities : SYNC
> Vendor_info : 'PHILIPS '
> Identifikation : 'CDD3600 CD-R/RW '
> Revision : '2.00'
> Device seems to be: Generic mmc CD-RW.
> Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
> Driver flags : SWABAUDIO
> Starting to write CD/DVD at speed 2 in write mode for single session.
> Last chance to quit, starting real write in 0 seconds. Operation starts.
> Track 01: Total bytes read/written: 624476160/624476160 (304920 sectors).
> cdrecord: Input/output error. close track/session: scsi sendcmd: no
> errorCDB: 5B 00 02 00 00 00 00 00 00 00
> status: 0x2 (CHECK CONDITION)
> Sense Bytes: F0 00 05 00 00 00 00 28 00 07 2A 24 2C 04 00 00
> Sense Key: 0x5 Illegal Request, Segment 0
> Sense Code: 0x2C Qual 0x04 (current program area is empty) Fru 0x0
> Sense flags: Blk 0 (valid)
> cmd finished after 0.018s timeout 480s
> cmd finished after 0.018s timeout 480s
>
> The scsi devices are :
>
> [kees@chocomel]# cat /proc/scsi/scsi
> Attached devices:
> Host: scsi0 Channel: 00 Id: 04 Lun: 00
> Vendor: PHILIPS Model: CDD3600 CD-R/RW Rev: 2.00
> Type: CD-ROM ANSI SCSI revision: 02
>
> Information on the Adaptec :
> [kees@chocomel]# cat /proc/scsi/aic7xxx/0
> Adaptec AIC7xxx driver version: 5.2.4/5.2.0
> Compile Options:
> TCQ Enabled By Default : Enabled
> AIC7XXX_PROC_STATS : Enabled
>
> Adapter Configuration:
> SCSI Adapter: Adaptec AHA-2940A Ultra SCSI host adapter
> Ultra Narrow Controller at PCI 0/11/0
> PCI MMAPed I/O Base: 0xe9800000
> Adapter SEEPROM Config: SEEPROM found and used.
> Adaptec SCSI BIOS: Enabled
> IRQ: 10
> SCBs: Active 0, Max Active 1,
> Allocated 31, HW 3, Page 255
> Interrupts: 24115
> BIOS Control Word: 0x10b6
> Adapter Control Word: 0x005c
> Extended Translation: Enabled
> Disconnect Enable Flags: 0x00ff
> Ultra Enable Flags: 0x0000
> Tag Queue Enable Flags: 0x0000
> Ordered Queue Tag Flags: 0x0000
> Default Tag Queue Depth: 32
> Tagged Queue By Device array for aic7xxx host instance 0:
> {0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0}
> Actual queue depth per device for aic7xxx host instance 0:
> {1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1}
>
> Statistics:
>
> (scsi0:0:4:0)
> Device using Narrow/Sync transfers at 10.0 MByte/sec, offset 15
> Transinfo settings: current(25/15/0/0), goal(25/15/0/0), user(25/15/0/0)
> Total transfers 9837 (9837 reads and 0 writes)
> < 2K 2K+ 4K+ 8K+ 16K+ 32K+ 64K+ 128K+
> Reads: 0 0 0 1 0 9836 0 0
> Writes: 0 0 0 0 0 0 0 0
>
> I hope somebody can help me with this one.
>
> Thanks,
> Kees Kuip
>
> --
> To UNSUBSCRIBE, email to [EMAIL PROTECTED]
> with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
