Indeed, you have to add routes and rules to routing table. Just bond them.
-----Original Message----- From: John Hearns [mailto:[email protected]] Sent: vrijdag 1 juni 2018 10:00 To: ceph-users Subject: Re: [ceph-users] iSCSI to a Ceph node with 2 network adapters - how to ? Errr.... is this very wise ? I have both its Ethernets connected to the same LAN, with different IPs in the same subnet (like, 192.168.200.230/24 and 192.168.200.231/24) In my experience setting up to interfaces on the same subnet means that your ssystem doesnt know which one to route traffic through... On 1 June 2018 at 09:01, Wladimir Mutel <[email protected]> wrote: Dear all, I am experimenting with Ceph setup. I set up a single node (Asus P10S-M WS, Xeon E3-1235 v5, 64 GB RAM, 8x3TB SATA HDDs, Ubuntu 18.04 Bionic, Ceph packages from http://download.ceph.com/debian-luminous/dists/xenial/ <http://download.ceph.com/debian-luminous/dists/xenial/> and iscsi parts built manually per http://docs.ceph.com/docs/master/rbd/iscsi-target-cli-manual-instal l/ <http://docs.ceph.com/docs/master/rbd/iscsi-target-cli-manual-install/> ) Also i changed 'chooseleaf ... host' into 'chooseleaf ... osd' in the CRUSH map to run with single host. I have both its Ethernets connected to the same LAN, with different IPs in the same subnet (like, 192.168.200.230/24 and 192.168.200.231/24) mon_host in ceph.conf is set to 192.168.200.230, and ceph daemons (mgr, mon, osd) are listening to this IP. What I would like to finally achieve, is to provide multipath iSCSI access through both these Ethernets to Ceph RBDs, and apparently, gwcli does not allow me to add a second gateway to the same target. It is going like this : /iscsi-target> create iqn.2018-06.host.test:test ok /iscsi-target> cd iqn.2018-06.host.test:test/gateways /iscsi-target...test/gateways> create p10s 192.168.200.230 skipchecks=true OS version/package checks have been bypassed Adding gateway, sync'ing 0 disk(s) and 0 client(s) ok /iscsi-target...test/gateways> create p10s2 192.168.200.231 skipchecks=true OS version/package checks have been bypassed Adding gateway, sync'ing 0 disk(s) and 0 client(s) Failed : Gateway creation failed, gateway(s) unavailable:192.168.200.231(UNKNOWN state) host names are defined in /etc/hosts as follows : 192.168.200.230 p10s 192.168.200.231 p10s2 so I suppose that something does not listen on 192.168.200.231, but I don't have an idea what is that thing and how to make it listen there. Or how to achieve this goal (utilization of both Ethernets for iSCSI) in different way. Shoud I aggregate Ethernets into a 'bond' interface with single IP ? Should I build and use 'lrbd' tool instead of 'gwcli' ? Is it acceptable that I run kernel 4.15, not 4.16+ ? What other directions could you give me on this task ? Thanks in advance for your replies. _______________________________________________ ceph-users mailing list [email protected] http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com <http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com> _______________________________________________ ceph-users mailing list [email protected] http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com
