Hello Bonding and iscsi are not a best practice architecture. Multipath is, however I can attest to problems with the multipathd and debian.
In any case, what you should try to do and check is: 1) Use two vlans, one for each ethernet port, with different ip address space. Your initiators on the hosts will then be able to discover two iscsi targets. 2) You should ensure that ping between host interfaces and iscsi targets is working. You should ensure that the iscsi target daemon is up (through the use of netstat for example) for each one of the two ip addresses/ethernet interfaces 3) Check multipath configuration On 18-06-01 05:08 +0200, Marc Roos wrote:
Indeed, you have to add routes and rules to routing table. Just bond them. -----Original Message----- From: John Hearns [mailto:hear...@googlemail.com] Sent: vrijdag 1 juni 2018 10:00 To: ceph-users Subject: Re: [ceph-users] iSCSI to a Ceph node with 2 network adapters - how to ? Errr.... is this very wise ? I have both its Ethernets connected to the same LAN, with different IPs in the same subnet (like, 192.168.200.230/24 and 192.168.200.231/24) In my experience setting up to interfaces on the same subnet means that your ssystem doesnt know which one to route traffic through... On 1 June 2018 at 09:01, Wladimir Mutel <m...@mwg.dp.ua> wrote: Dear all, I am experimenting with Ceph setup. I set up a single node (Asus P10S-M WS, Xeon E3-1235 v5, 64 GB RAM, 8x3TB SATA HDDs, Ubuntu 18.04 Bionic, Ceph packages from http://download.ceph.com/debian-luminous/dists/xenial/ <http://download.ceph.com/debian-luminous/dists/xenial/> and iscsi parts built manually per http://docs.ceph.com/docs/master/rbd/iscsi-target-cli-manual-instal l/ <http://docs.ceph.com/docs/master/rbd/iscsi-target-cli-manual-install/> ) Also i changed 'chooseleaf ... host' into 'chooseleaf ... osd' in the CRUSH map to run with single host. I have both its Ethernets connected to the same LAN, with different IPs in the same subnet (like, 192.168.200.230/24 and 192.168.200.231/24) mon_host in ceph.conf is set to 192.168.200.230, and ceph daemons (mgr, mon, osd) are listening to this IP. What I would like to finally achieve, is to provide multipath iSCSI access through both these Ethernets to Ceph RBDs, and apparently, gwcli does not allow me to add a second gateway to the same target. It is going like this : /iscsi-target> create iqn.2018-06.host.test:test ok /iscsi-target> cd iqn.2018-06.host.test:test/gateways /iscsi-target...test/gateways> create p10s 192.168.200.230 skipchecks=true OS version/package checks have been bypassed Adding gateway, sync'ing 0 disk(s) and 0 client(s) ok /iscsi-target...test/gateways> create p10s2 192.168.200.231 skipchecks=true OS version/package checks have been bypassed Adding gateway, sync'ing 0 disk(s) and 0 client(s) Failed : Gateway creation failed, gateway(s) unavailable:192.168.200.231(UNKNOWN state) host names are defined in /etc/hosts as follows : 192.168.200.230 p10s 192.168.200.231 p10s2 so I suppose that something does not listen on 192.168.200.231, but I don't have an idea what is that thing and how to make it listen there. Or how to achieve this goal (utilization of both Ethernets for iSCSI) in different way. Shoud I aggregate Ethernets into a 'bond' interface with single IP ? Should I build and use 'lrbd' tool instead of 'gwcli' ? Is it acceptable that I run kernel 4.15, not 4.16+ ? What other directions could you give me on this task ? Thanks in advance for your replies. _______________________________________________ ceph-users mailing list ceph-users@lists.ceph.com http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com <http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com> _______________________________________________ ceph-users mailing list ceph-users@lists.ceph.com http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com
-- -- Panayiotis Gotsis Systems & Services Engineer Network Operations Center GRNET - Networking Research and Education 7, Kifisias Av., 115 23, Athens t: +30 210 7471091 | f: +30 210 7474490 Follow us: www.grnet.gr Twitter: @grnet_gr |Facebook: @grnet.gr LinkedIn: grnet |YouTube: GRNET EDET _______________________________________________ ceph-users mailing list ceph-users@lists.ceph.com http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com
