Rick, The procedure is the same for the TPI system. I didn't catch that in your 
post. What is important is that you are getting WOT and that the plunger get's 
fully stroked.
Mike
  ----- Original Message ----- 
  From: Rick Schaefer 
  To: The Chevelle Mailing List 
  Sent: Wednesday, September 26, 2007 3:05 PM
  Subject: Re: [Chevelle-list] 700r4 TV Cable Adjustment


    Thank You Dale, that should work most excellently!     And  Mike thanx for 
the information.   This is for a TPI system, not carb.   But I know that the 
procedure is the same, just different bracket.  That info looks  very familiar, 
I forgot about it.      I used that procedure when I first installed the 700 
with a carburetor .    Messy but I know it works. 


  On 9/26/07, Mike Holleman <[EMAIL PROTECTED]> wrote: 
    Rick, The best way to set the TV cable requires the pan off the trans. You 
disconnect the TV cable at the carb, make sure the throttle is giving you WOT. 
Then connect the cable and get a friend to mash the pedal to WOT. The plunger 
that is activated by the TV cable needs to be fully pushed into the valve body, 
basically flushed. If it is not adjust the cable tension until it is.  If you 
are using BTO's brackets on the carb end and a Lokar cable, this is the basic 
adjustment. If you are just changing out a cable you need not worry about any 
pressure settings. 
    Mike Holleman
      ----- Original Message ----- 
      From: Rick Schaefer 
      To: The Chevelle Mailing List 
      Sent: Wednesday, September 26, 2007 10:41 AM
      Subject: Re: [Chevelle-list] 700r4 TV Cable Adjustment

       
        Thanx Brad, but that particular post & most everything else I've 
googled refer to a stock cable.  There is no tab to push down with the LOKAR 
cable.  Its a braided cable, adjusted by movement of lock nuts at the mount 
bracket.   

        The TV Made EZ page & its links give the procedure with a braided 
cable, but not the specific pressures to look for.   Bowtie OD wants you to 
record the pressues, email them, and then they tell you what adjustments to 
make (as far as I could find). 
       
         Late last nite I found a Swedish (I think) web site thgat gave the 
pressures in KpA (??) and if I can find some type of conversion chart it may 
help.  Any more info will sure be appreciated.  I've had great luck & 
reliability with this tranny for 10 years & don't want to burn it up now. 
       
      On 9/26/07, Brad Waller <[EMAIL PROTECTED]> wrote: 
        Rick Schaefer wrote: 
             Does anyone have instructions/advice for adjusting the TV cable on 
my 700?   I am using a LOKAR TV Cable & Bracket on a TPI motor, not the stock 
zip & click stock cable.    When I installed it several years ago, I adjusted 
it using a gauge and had to read specific pressure ranges for each gear.  I 
can't find the info used back then.  Thanx 

          -- 
          Rick Schaefer
          72 TPI El Camino


        One reference (from Corvette Forum):
        The TV cable adjustment is made on the side of the carb. It is 
something that can be done in a few minutes. If your pivot point is correct all 
you do is push in the metal tab on the cable mount and push the nose towards 
the firewall or into the mounting bracket then take the carb throttle linkage 
and give it full throttle until the cable ratcheted out and the butterflies of 
the carb are at full throttle position. This should adjust the TV cable 
correctly. If you make the cable shorter by pushing it into the body the shifts 
are alot harder You can try this but the 1st time you floor it the cable will 
self adjust. I mentioned the throttle stud must be in the correct location so 
that at a given throttle position the TV cable is pulled out the correct amount 
for line pressure. I have these demensions but not here. The shop that rebuilt 
my transmission wanted my copy for their files. Remember to adjust the TV cable 
nothing but the aircleaner must come off. 

        Chevelle Forum: 
http://www.chevelles.com/forums/archive/index.php/t-79170.html 

        Bowtie Overdrives has a detailed PDF on this and more:
        http://www.bowtieoverdrives.com/Instructions/TV_101-1.pdf 

        You can also read a few other sites:
        http://www.gnttype.org/techarea/transmission/tvcable.html 
        http://www.transmissioncenter.net/subject.htm

        -- 

Brad Waller 


      -- 
      Rick Schaefer
      72 TPI El Camino




--------------------------------------------------------------------------


      No virus found in this incoming message.
      Checked by AVG Free Edition. 
      Version: 7.5.488 / Virus Database: 269.13.30/1030 - Release Date: 
9/25/2007 8:02 AM






  -- 
  Rick Schaefer
  72 TPI El Camino




------------------------------------------------------------------------------


  No virus found in this incoming message.
  Checked by AVG Free Edition. 
  Version: 7.5.488 / Virus Database: 269.13.30/1030 - Release Date: 9/25/2007 
8:02 AM

Reply via email to