Well I ran into my first problem. I tried to add an ssid to the ap, then added a sub interface on f0 and on dot11radio0, and now it seems as if the radio is not bridging the traffic correctly and the trunk is not working on the switch.
Here is my config Switch configuration: interface FastEthernet0/1 switchport access vlan 500 switchport trunk native vlan 500 switchport trunk allowed vlan 160,200,500 switchport mode trunk The trunk is only showing 200 in forwarding state. I need 160 and 500 forwarded. AP configuration: ! dot11 ssid blsd vlan 500 authentication open authentication shared authentication key-management wpa mbssid guest-mode wpa-psk ascii 7 xxxxxxxxxx ! dot11 ssid raec vlan 160 authentication open authentication shared authentication key-management wpa mbssid guest-mode wpa-psk ascii 7 xxxxxxxxxx ! dot11 network-map power inline negotiation injector override power inline negotiation prestandard source ! ! bridge irb ! ! interface Dot11Radio0 no ip address no ip route-cache ! encryption vlan 500 mode ciphers aes-ccm ! encryption vlan 160 mode ciphers aes-ccm ! ssid blsd ! ssid raec ! mbssid station-role root bridge-group 1 bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled ! interface Dot11Radio0.160 encapsulation dot1Q 160 no ip route-cache bridge-group 2 bridge-group 2 subscriber-loop-control bridge-group 2 block-unknown-source no bridge-group 2 source-learning no bridge-group 2 unicast-flooding bridge-group 2 spanning-disabled ! interface Dot11Radio0.500 encapsulation dot1Q 500 no ip route-cache bridge-group 3 bridge-group 3 subscriber-loop-control bridge-group 3 block-unknown-source no bridge-group 3 source-learning no bridge-group 3 unicast-flooding bridge-group 3 spanning-disabled ! interface FastEthernet0 no ip address no ip route-cache duplex auto speed auto bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled hold-queue 160 in ! interface FastEthernet0.160 encapsulation dot1Q 160 no ip route-cache bridge-group 2 no bridge-group 2 source-learning bridge-group 2 spanning-disabled ! interface FastEthernet0.500 encapsulation dot1Q 500 no ip route-cache bridge-group 3 no bridge-group 3 source-learning bridge-group 3 spanning-disabled ! interface BVI1 ip address 192.168.50.151 255.255.255.0 no ip route-cache ! bridge 1 route ip ! I'm guessing there is something wrong with the bridge configuration. Dan. On Dec 17, 2007 9:22 PM, Tom Storey <[EMAIL PROTECTED]> wrote: > > Thanks Tom! Everything worked great. I have a couple of questions: > > Not a worry :-) > > > > > If I copy this configuration to my other ap's in the building will a > > client(notebook) automatically roam from ap to ap without getting > > disconnected? > > That I am unsure of. > > > Do you have 802.11a clients or is the 802.11a radio used for something > > else? > > I dont have any 11a clients just yet, only 11b. > > > How would I setup the AP so there is a minimum signal level that is > > allowed? eg, if a user is outside the building and still connected that > > it > > won't work if the users device is say past -75db... > > > > Transmit power of the interface can be adjusted using the "power local x" > command, where x is the level of power to be run at. Best perform that on > your APs and see what they offer. > > > Also, I accidentally ordered LWAPP's and I have converted them back to > > autonomous ap's. Is there any difference between a converted one vs a > > bought autonomous ap? > > They are exactly the same, the only difference is the software running on > them. > > > > > Thanks, > > Dan. > > > > On Dec 5, 2007 6:23 PM, Tom Storey <[EMAIL PROTECTED]> wrote: > > > >> > Hello, > >> > > >> > I'm new to using access points and what I would like to do is setup > an > >> > 1131ag with a trunk to a 2960 switch, then have two different ssid's > >> which > >> > would be mapped to two different vlan's on the 2960. Does anyone > have > >> an > >> > example config for something like this? > >> > > >> > Thanks, > >> > Dan. > >> > >> This is the config Im currently using between a 3524XL and 1242AG, the > >> config should be fairly similar if not exactly the same for a 1131AG. > >> > >> > >> Switch port: > >> > >> interface FastEthernet0/4 > >> description ** Trunk to Fa0 on ap1 ** > >> duplex full > >> speed 100 > >> switchport trunk encapsulation dot1q > >> switchport multi vlan 3,5 > >> switchport mode trunk > >> ! > >> > >> > >> AP specifics: > >> > >> dot11 vlan-name open-vlan vlan 5 > >> dot11 vlan-name closed-vlan vlan 3 > >> ! > >> dot11 ssid open-wlan > >> vlan open-vlan > >> authentication open > >> mbssid guest-mode > >> ! > >> dot11 ssid closed-wlan > >> vlan closed-vlan > >> authentication open > >> authentication key-management wpa > >> mbssid guest-mode > >> wpa-psk ascii xxxxxxxxxx > >> ! > >> bridge irb > >> ! > >> interface Dot11Radio0 > >> description ** 802.11b/g Radio ** > >> no ip address > >> no ip route-cache > >> load-interval 30 > >> ! > >> encryption vlan closed-vlan mode ciphers aes-ccm > >> ! > >> ssid open-wlan > >> ! > >> ssid closed-wlan > >> ! > >> mbssid > >> speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 > >> 36.0 48.0 54.0 > >> station-role root > >> bridge-group 1 > >> bridge-group 1 block-unknown-source > >> no bridge-group 1 source-learning > >> no bridge-group 1 unicast-flooding > >> bridge-group 1 spanning-disabled > >> ! > >> interface Dot11Radio0.3 > >> encapsulation dot1Q 3 > >> no ip route-cache > >> bridge-group 3 > >> bridge-group 3 subscriber-loop-control > >> bridge-group 3 block-unknown-source > >> no bridge-group 3 source-learning > >> no bridge-group 3 unicast-flooding > >> bridge-group 3 spanning-disabled > >> ! > >> interface Dot11Radio0.5 > >> encapsulation dot1Q 5 > >> no ip route-cache > >> bridge-group 5 > >> bridge-group 5 subscriber-loop-control > >> bridge-group 5 block-unknown-source > >> no bridge-group 5 source-learning > >> no bridge-group 5 unicast-flooding > >> bridge-group 5 spanning-disabled > >> ! > >> interface Dot11Radio1 > >> description ** 802.11a Radio ** > >> no ip address > >> no ip route-cache > >> load-interval 30 > >> ! > >> encryption vlan closed-vlan mode ciphers aes-ccm > >> ! > >> ssid open-wlan > >> ! > >> ssid closed-wlan > >> ! > >> no dfs band block > >> mbssid > >> speed basic-6.0 9.0 basic-12.0 18.0 basic-24.0 36.0 48.0 54.0 > >> channel dfs > >> station-role root > >> bridge-group 1 > >> bridge-group 1 block-unknown-source > >> no bridge-group 1 source-learning > >> no bridge-group 1 unicast-flooding > >> bridge-group 1 spanning-disabled > >> ! > >> interface Dot11Radio1.3 > >> encapsulation dot1Q 3 > >> no ip route-cache > >> bridge-group 3 > >> bridge-group 3 subscriber-loop-control > >> bridge-group 3 block-unknown-source > >> no bridge-group 3 source-learning > >> no bridge-group 3 unicast-flooding > >> bridge-group 3 spanning-disabled > >> ! > >> interface Dot11Radio1.5 > >> encapsulation dot1Q 5 > >> no ip route-cache > >> bridge-group 5 > >> bridge-group 5 subscriber-loop-control > >> bridge-group 5 block-unknown-source > >> no bridge-group 5 source-learning > >> no bridge-group 5 unicast-flooding > >> bridge-group 5 spanning-disabled > >> ! > >> interface FastEthernet0 > >> description ** Trunk to Fa0/4 on sw1 ** > >> no ip address > >> no ip route-cache > >> load-interval 30 > >> speed 100 > >> full-duplex > >> bridge-group 1 > >> no bridge-group 1 source-learning > >> bridge-group 1 spanning-disabled > >> hold-queue 160 in > >> ! > >> interface FastEthernet0.3 > >> encapsulation dot1Q 3 > >> no ip route-cache > >> bridge-group 3 > >> no bridge-group 3 source-learning > >> bridge-group 3 spanning-disabled > >> ! > >> interface FastEthernet0.5 > >> encapsulation dot1Q 5 > >> no ip route-cache > >> bridge-group 5 > >> no bridge-group 5 source-learning > >> bridge-group 5 spanning-disabled > >> ! > >> interface BVI1 > >> description ** Management Interface ** > >> ip address 172.25.84.8 255.255.255.240 > >> no ip route-cache > >> ! > >> bridge 1 route ip > >> ! > >> > >> > > > > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
