Hi Phil, Thanks, your idea to mark as DSCP, and then rely on DSCP-COS translation did the trick.
policy-map set-dscp-ef class class-default set dscp ef On Sun, 2008-02-10 at 08:34 -0500, Phil Bedard wrote: > If the port is marked as untrusted, the PFC still marks the packet > with an internal DSCP value of 0 on ingress, so the "mls qos cos 5" > command in this instance won't do what you want. You can configure > the "mls qos marking ignore port-trust" command, then the PFC will not > rewrite the port cos value you set. Another option is to use a > policy-map to set certain traffic to trusted. You could also set the > ingress DSCP value with a policy-map and use the dscp-to-CoS map to > set the correct egress cos. The default map sets DSCP 40-46 to 5 > (divides by 8). > > > There may be another way as well that I'm missing. I don't know that > setting the port to trusted state will work, I believe for a trunk it > will ignore the mls qos cos value. > > > Phil > > > > > On Feb 9, 2008, at 6:20 PM, Vladimir Ivashchenko wrote: > > > Just to make sure I'm clear: "802.1p value for packets going out > > from Gig2/1 is set to 0" - I mean packets received > > from Gig2/1, going to the Linux box on another interface, have CoS > > bits set to 0, despite "mls qos cos 5" on the > > Gig2/1. The sniffer is running on the Linux box. > > > > On Sun, Feb 10, 2008 at 12:31:37AM +0200, Vladimir Ivashchenko > > wrote: > > > > > Hi List, > > > > > > We cannot get Cat6500 to rewrite CoS values (802.1p bits). > > > > > > Configuration is > > > > > > mls qos > > > no mls flow ip > > > no mls flow ipv6 > > > no mls qos rewrite ip dscp > > > no mls acl tcam share-global > > > mls cef error action freeze > > > > > > interface GigabitEthernet2/1 > > > switchport > > > switchport trunk encapsulation dot1q > > > switchport mode trunk > > > no ip address > > > load-interval 30 > > > wrr-queue queue-limit 40 30 > > > mls qos cos 5 > > > no cdp enable > > > spanning-tree portfast trunk > > > no mls qos trust > > > > > > We have a sniffer connected to dot1q trunk on another port. The > > > sniffer shows that 802.1p value for packets going out > > > from Gig2/1 is set to 0. We have tried searching Cisco site and > > > playing with various commands, but did not succeed. IOS > > > 12.2(18)SXF5. > > > > > > Catalyst 3560 has "mls qos cos override" command, which seems to > > > do the trick, but this command is not available on > > > Catalyst 6500. > > > > > > -- > > > Best Regards > > > Vladimir Ivashchenko > > > Chief Technology Officer > > > PrimeTel, Cyprus - www.prime-tel.com > > > _______________________________________________ > > > cisco-nsp mailing list [email protected] > > > https://puck.nether.net/mailman/listinfo/cisco-nsp > > > archive at http://puck.nether.net/pipermail/cisco-nsp/ > > > > -- > > Best Regards > > Vladimir Ivashchenko > > Chief Technology Officer > > PrimeTel, Cyprus - www.prime-tel.com > > _______________________________________________ > > cisco-nsp mailing list [email protected] > > https://puck.nether.net/mailman/listinfo/cisco-nsp > > archive at http://puck.nether.net/pipermail/cisco-nsp/ > -- Best Regards, Vladimir Ivashchenko Chief Technology Officer PrimeTel PLC, Cyprus - www.prime-tel.com _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
