Those are both commands available in Native IOS. I don't know if they are available in Hybrid, although it would be nice to know if they were.
-- http://dcp.dcptech.com > -----Original Message----- > From: Tassos Chatzithomaoglou [mailto:[EMAIL PROTECTED] > Sent: Wednesday, March 26, 2008 6:40 AM > To: David Prall > Cc: 'Adam Greene'; [email protected] > Subject: Re: [c-nsp] 6509 noob question > > The following two could probably help you too: > > remote command switch xxx > remote login switch > > -- > Tassos > > > David Prall wrote on 25/3/2008 11:05 μμ: > > Switch console can only be done from catos. You want to > find and entry that > > has a mac address within the cisco range. What does "sh cdp > neighbor" give > > you. I don't remember this working, but it has been a long > time. Then "sh > > cdp neighbor detail" for the address. Might get lucky. > > > > David > > > > -- > > http://dcp.dcptech.com > > > > > >> -----Original Message----- > >> From: Adam Greene [mailto:[EMAIL PROTECTED] > >> Sent: Tuesday, March 25, 2008 4:58 PM > >> To: David Prall; [email protected] > >> Subject: Re: [c-nsp] 6509 noob question > >> > >> Thanks, all. > >> > >> Neither the session nor switch console commands are > >> recognized on the IOS > >> side. > >> > >> Is there anything specific I should look for in the ARP > >> table? There are > >> about 1000 entries in there. > >> > >> I guess next step will be to call this switch's admin .... > >> > >> thanks, > >> Adam > >> > >> ----- Original Message ----- > >> From: "David Prall" <[EMAIL PROTECTED]> > >> To: "'Adam Greene'" <[EMAIL PROTECTED]>; > >> <[email protected]> > >> Sent: Tuesday, March 25, 2008 4:45 PM > >> Subject: RE: [c-nsp] 6509 noob question > >> > >> > >>> You need the management interface address for the catos > >> side, from their > >>> you > >>> can session to the msfc/msfc's. Can telnet from the msfc to > >> the catos side > >>> if you know the address. Might be able to figure out where > >> it is from the > >>> arp table. > >>> > >>> David > >>> > >>> -- > >>> http://dcp.dcptech.com > >>> > >>> > >>>> -----Original Message----- > >>>> From: [EMAIL PROTECTED] > >>>> [mailto:[EMAIL PROTECTED] On Behalf Of > Adam Greene > >>>> Sent: Tuesday, March 25, 2008 4:20 PM > >>>> To: [email protected] > >>>> Subject: [c-nsp] 6509 noob question > >>>> > >>>> How's this for a stupid question? > >>>> > >>>> I'm working remotely on a pair of 6509's: CatOS 8.3(3) / IOS > >>>> 12.1(8a)E3. > >>>> > >>>> I can telnet to the devices and access the IOS CLI. > >>>> > >>>> The million-dollar question: how to I access the CatOS CLI? > >>>> > >>>> As far as I can tell all the switch configs live in CatOS > >>>> while the routing configs live in IOS, and I'm trying to gain > >>>> access to the spanning-tree info (CatOS), to see if the > >>>> switch is running PVST+, MST or what. > >>>> > >>>> Thanks, > >>>> Adam > >>>> _______________________________________________ > >>>> cisco-nsp mailing list [email protected] > >>>> https://puck.nether.net/mailman/listinfo/cisco-nsp > >>>> archive at http://puck.nether.net/pipermail/cisco-nsp/ > >>> > >>> > >>> > >>> > >>> > >> > >> > >> > > > > _______________________________________________ > > cisco-nsp mailing list [email protected] > > https://puck.nether.net/mailman/listinfo/cisco-nsp > > archive at http://puck.nether.net/pipermail/cisco-nsp/ > > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
