Dear Rodney yes that is EIGRP graceful restart feature which is supported since IOS 12.2(15)T . and i believe it is supported in all platforms
Jeff , can u provide us with show ip protocols and show version from your router . best regards --Abo Zaid On 4/22/08, Rodney Dunn <[EMAIL PROTECTED]> wrote: > > resync is one thing....drop is another. > > In newer code we don't drop but we do resync. ;) > > R1_#sh run | section router eigrp > router eigrp 1 > network 0.0.0.0 > auto-summary > R1_#config t > Enter configuration commands, one per line. End with CNTL/Z. > R1_(config)#router ei 1 > R1_(config-router)#distribute-list 1 out > R1_(config-router)#exit > R1_(config)#access-list 1 deny 4.0.0.0 > R1_(config)#access-list 1 permit 2.2.2.0 > R1_(config)#end > R1_# > *Apr 22 13:24:16.184: %SYS-5-CONFIG_I: Configured from console by console > R1_# > *Apr 22 13:24:20.972: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 1: Neighbor > 2.2.2.2(Ethernet1/0) is resync: route configuration changed > R1_# > > > and on the peer: > > *Apr 22 13:24:20.544: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 1: Neighbor > 2.2.2.1(Ethernet1/0) is resync: peer graceful-restart > > > Rodney > > On Tue, Apr 22, 2008 at 07:08:46AM +0200, Ibrahim Abo Zaid wrote: > > Hi All > > > > Yes , this is a normal behaviour to EIGRP to resync topology table > between > > neighbors after modifying the redistribute-list > > > > best regards > > --Abo Zaid > > > > On 4/21/08, [EMAIL PROTECTED] <[EMAIL PROTECTED]> wrote: > > > > > > Sadly, it is. > > > > > > -- > > > Regards, > > > > > > Jason Plank > > > CCIE #16560 > > > e: [EMAIL PROTECTED] > > > > > > -------------- Original message ---------------------- > > > From: "Jeff Cartier" <[EMAIL PROTECTED]> > > > > Ah nevermind. Looks like its normal behaviour... *sigh* > > > > > > > > > > > > -----Original Message----- > > > > From: [EMAIL PROTECTED] on behalf of Jeff Cartier > > > > Sent: Mon 4/21/2008 3:59 PM > > > > To: [email protected] > > > > Subject: [c-nsp] EIGRP - modify distribute-list and EIGRP neighbor > drops > > > > > > > > > > > > Greetings! > > > > > > > > I've coming into an unfamiliar issue where I'm modifying the > > > distribution list > > > > on a Cisco router running EIGRP...I'm creating a vlan management > subnet > > > using > > > > loopbacks and vlan SVIs; the thing I'm having trouble explaining is > when > > > I > > > > modify the ACL, which is a standard ACL, to permit the subnets that > I > > > want to > > > > redistribute, the EIGRP neighbors drop and then re-connect. > > > > > > > > Why is this? > > > > _______________________________________________ > > > > cisco-nsp mailing list [email protected] > > > > https://puck.nether.net/mailman/listinfo/cisco-nsp > > > > archive at http://puck.nether.net/pipermail/cisco-nsp/ > > > > > > > > _______________________________________________ > > > > cisco-nsp mailing list [email protected] > > > > https://puck.nether.net/mailman/listinfo/cisco-nsp > > > > archive at http://puck.nether.net/pipermail/cisco-nsp/ > > > > > > _______________________________________________ > > > cisco-nsp mailing list [email protected] > > > https://puck.nether.net/mailman/listinfo/cisco-nsp > > > archive at http://puck.nether.net/pipermail/cisco-nsp/ > > > > > _______________________________________________ > > cisco-nsp mailing list [email protected] > > https://puck.nether.net/mailman/listinfo/cisco-nsp > > archive at http://puck.nether.net/pipermail/cisco-nsp/ > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
