Zenon, Can you please explain specifically what you want to rate limit... Maybe a show ip mroute could be helpful...
Arie -----Original Message----- From: Zenon Mousmoulas [mailto:[EMAIL PROTECTED] Sent: Sunday, June 15, 2008 22:48 PM To: Arie Vayner (avayner) Cc: Hank Nussbacher; [email protected] Subject: Re: [c-nsp] ip multicast rate-limit Hi Arie, I would like to ask you something: The ip multicast rate-limit command, when used with a group-list and/ or source-list argument, does policing on a per-mroute (S,G or *,G) basis. This is according to relevant IOS documentation and this document: ftp://ftpeng.cisco.com/ipmulticast/config-notes/multicast-rate-limit.txt The above (perhaps outdated) document suggests (in section "Status") to use CAR for per-interface (aggregate) traffic rate-limiting, but to keep using this command for per-mroute applications. Has this changed since 2001? Could you suggest how to build a policy that would apply at per-mroute (or higher, i.e. per-flow) granularity, instead of being applied on the aggregate matched traffic? Would this sort of granular policing fall within the scope of the microflow policing feature, which is available on some 7600 and Catalyst 6500 hardware? Best regards, Zenon Mousmoulas GRNET On 14 Ιουν 2008, at 9:52 ΜΜ, Arie Vayner (avayner) wrote: > I suggest you try using a regular policy map, building a class with > the traffic matched in an ACL, and apply a regular police policy on > that class... > Arie > > -----Original Message----- > From: Hank Nussbacher [mailto:[EMAIL PROTECTED] > Sent: Saturday, June 14, 2008 21:50 PM > To: Arie Vayner (avayner) > Cc: [email protected]; Zenon Mousmoulas > Subject: RE: [c-nsp] ip multicast rate-limit > > On Sat, 14 Jun 2008, Arie Vayner (avayner) wrote: > >> Hank, >> >> What are you trying to achieve? >> Can you please share "show module"? > > Trying to limit SAP storms. > > 11 0 4-subslot SPA Interface Processor-400 7600-SIP-400 > JAE12035DJ5 > 11/0 1xOC48 POS/RPR SPA SPA-1XOC48POS/RPR JAE11441NKV 2.3 > Ok > > -Hank > >> >> Thanks >> Arie >> >> -----Original Message----- >> From: [EMAIL PROTECTED] >> [mailto:[EMAIL PROTECTED] On Behalf Of Hank >> Nussbacher >> Sent: Thursday, June 12, 2008 16:02 PM >> To: [email protected] >> Cc: Zenon Mousmoulas >> Subject: [c-nsp] ip multicast rate-limit >> >> http://www.cisco.com/en/US/docs/ios/ipmulti/command/reference/ >> imc_03.h >> tm >> l#wp1016097 >> In 12.2(18)SXF11: >> >> petach-tikva-gp(config)#int pos11/0/0 petach-tikva-gp(config-if)#ip >> multicast rate-limit in group-list SAP-mcast-group 1000 "ip >> multicast rate-limit" command is not supported >> >> So I go to: >> http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/ >> 12.2SXF/ >> na >> tive/release/notes/OL_4164.html >> where it says: >> "The ip multicast rate-limit command is not supported on LAN ports. >> (CSCds22281)" >> >> So what 12.2SX version supports ip multicast rate-limit on a POS >> interface? >> >> Thanks, >> Hank >> >> _______________________________________________ >> cisco-nsp mailing list [email protected] >> https://puck.nether.net/mailman/listinfo/cisco-nsp >> archive at http://puck.nether.net/pipermail/cisco-nsp/ >> _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
