What code rev is in there? Thanks, Chris
On 10/20/08 3:20 AM, "Brian Turnbow" <[EMAIL PROTECTED]> wrote: > Please don't tell that to this router > > > policy-map llq > class sipRTP > priority 512 > class class-default > fair-queue > random-detect > > vc-class atm CVPHDSL-VoIP > vbr-nrt 1524 1524 > encapsulation aal5snap > > interface ATM3/0.20842 point-to-point > description cust 1 > ip address192.168.0.41 255.255.255.252 > pvc CVPH_CUSTVOIP 208/42 > class-vc CVPHDSL-VoIP > service-policy out llq > > 7200-accessjn3#sh policy-map int ATM3/0.20842 > ATM3/0.20842: VC 208/42 - > > Service-policy output: llq > > queue stats for all priority classes: > > queue limit 64 packets > (queue depth/total drops/no-buffer drops) 0/0/0 > (pkts output/bytes output) 5466056/418685691 > > Class-map: sipRTP (match-all) > 5466056 packets, 418685691 bytes > 5 minute offered rate 61000 bps, drop rate 0 bps > Match: access-group 5 > Priority: 512 kbps, burst bytes 12800, b/w exceed drops: 0 > > Class-map: class-default (match-any) > 492783 packets, 493906760 bytes > 5 minute offered rate 509000 bps, drop rate 0 bps > Match: any > 492783 packets, 493906760 bytes > 5 minute rate 509000 bps > Queueing > queue limit 64 packets > (queue depth/total drops/no-buffer drops/flowdrops) 0/50/0/50 > (pkts output/bytes output) 492733/493866217 > Fair-queue: per-flow queue limit 16 > Exp-weight-constant: 9 (1/512) > Mean queue depth: 0 packets > class Transmitted Random drop Tail/Flow drop Minimum > Maximum Mark > pkts/bytes pkts/bytes pkts/bytes thresh > thresh prob > > 0 486842/493318682 0/0 50/40543 > 20 40 1/10 > 1 54/22464 0/0 0/0 > 22 40 1/10 > 2 6/746 0/0 0/0 > 24 40 1/10 > 3 0/0 0/0 0/0 > 26 40 1/10 > 4 5/330 0/0 0/0 > 28 40 1/10 > 5 20/1200 0/0 0/0 > 30 40 1/10 > 6 5753/515372 0/0 0/0 > 32 40 1/10 > 7 53/7423 0/0 0/0 > 34 40 1/10 > > http://www.cisco.com/en/US/tech/tk39/tk824/technologies_configuration_example0 > 9186a0080094cf6.shtml > > > Brian > > > > > > From: Victor Cappuccio [mailto:[EMAIL PROTECTED] > Sent: venerdì 17 ottobre 2008 18.52 > To: Brian Turnbow > Cc: Networkers; [email protected] > Subject: Re: [c-nsp] 7206VXR and CBWFQ > > Hi, > > Subinterfaces and software interfaces do not have their own separate transmit > (Tx) ring; therefore, no congestion can occur. These interface types include > dialers, tunnels, and Frame Relay subinterfaces, and will only congest when > their main hardware interface Tx ring congests. The Tx ring state is an > indication of congestion for software interfaces. > > > router(config)# interface Serial0/0.1 > router(config-subif)# service-policy output test > CBWFQ : Not supported on subinterfaces > > > 1.- Create a child or lower-level policy that configures a queueing mechanism. > In the example below, we configure LLQ using the priority command and CBWFQ > using the bandwidth command. Refer to Congestion Management Overview for more > information. > > policy-map child > class voice > priority 512 > > 2. Create a parent or top-level policy that applies class-based shaping. Apply > the child policy as a command under the parent policy since the admission > control for the child class is done based on the shaping rate for the parent > class. > > policy-map parent > class class-default > shape average 2000000 > service-policy child > > 3. Apply the parent policy to the subinterface. > > interface Serial0/0.1 > service-policy parent > > Cisco Page: http://tinyurl.com/ytt8ge > > Note: Class-based shaping works at the interface and subinterface level. Cisco > IOS 12.2(2.5) introduces the ability to configure shaping on the main > interface and IP addresses on the subinterfaces. > > thanks, > > Victor Cappuccio > CCIE R/S# 20657 > CCSI# 30452 > www.anetworkerblog.com <http://www.anetworkerblog.com> > > On Fri, Oct 17, 2008 at 6:19 PM, Brian Turnbow <[EMAIL PROTECTED]> wrote: >> Your pvc needs to be abr/vbr/cbr >> You can't do it on ubr >> >> Regards >> >> Brian >> >> >> >> >> >> >> -----Original Message----- >> From: [EMAIL PROTECTED] >> [mailto:[EMAIL PROTECTED] On Behalf Of Networkers >> >> Sent: venerdì 17 ottobre 2008 17.10 >> To: [email protected] >> Subject: [c-nsp] 7206VXR and CBWFQ >> >> >> >> >> Whenever I try to apply the following I get an error message about how >> CBWFQ can't be applied to subinterfaces. What is the correct way to do >> this? >> >> Thanks, >> Chris >> >> class-map match-any VOIP >> match ip dscp ef >> match precedence 5 >> class-map match-all CRITICAL >> match access-group 100 >> >> policy-map MyCBWFQ >> class CRITICAL >> priority 48 >> class VOIP >> bandwidth 320 >> set precedence 6 >> >> vc-class atm MyClass >> ubr 1536 >> encapsulation aal5mux ppp Virtual-Template5 >> >> interface Virtual-Template5 >> ip unnumbered Loopback0 >> service-policy output MyCBWFQ >> peer default ip address pool default >> ppp authentication pap callin >> >> interface ATM2/0.1921 point-to-point >> pvc 1/1921 >> class-vc MyClass >> >> >> >> >> >> >> >> _______________________________________________ >> cisco-nsp mailing list [email protected] >> https://puck.nether.net/mailman/listinfo/cisco-nsp >> archive at http://puck.nether.net/pipermail/cisco-nsp/ >> _______________________________________________ >> cisco-nsp mailing list [email protected] >> https://puck.nether.net/mailman/listinfo/cisco-nsp >> archive at http://puck.nether.net/pipermail/cisco-nsp/ > > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
