Larry Smith wrote:
t1 26 channel-group 0 timeslots 1-24
t1 27 channel-group 0 timeslots 1-24
t1 28 channel-group 0 timeslots 1-24
controller T3 5/0
framing m23
clock source line
cablelength 10
t1 1 channel-group 0 timeslots 1-24
t1 2 channel-group 1 timeslots 1-24
t1 3 channel-group 2 timeslots 1-12
Morning, Larry. Do you know if the channel-group # is significant to
each DS1 or does the channel-group # have to be unique across the DS3?
I'm thinking that it's unique to the DS1 so that you can create X number
of channel-groups on a DS1 if needed but I'm not 100% on that.
t1 1 clock source Line
Do you think I should generate clocking on our router or on the mux? We
don't have an external clock source in that CO. I expect to have up to
a dozen different M13s connected to this 7206 as time goes by. Would it
be a problem if the 7206 received clocking on each DS3 from each of the
muxes or would that screw things up internally? At this point I don't
expect to get handed a T1 w/ clocking from the RBOC. All the CPEs will
be line of course.
On your virtual, what does it show:
7206:
Serial1/0/1:0 is down, line protocol is down
Hardware is PA-MC-2T3-EC
Internet address is 1.1.1.1/24
MTU 1500 bytes, BW 1536 Kbit/sec, DLY 20000 usec,
reliability 253/255, txload 1/255, rxload 1/255
Encapsulation HDLC, crc 16, loopback not set
Keepalive set (10 sec)
Last input 18:15:59, output never, output hang never
Last clearing of "show interface" counters 00:00:07
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/16 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 1152 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions alarm present
VC:0 Timeslot(s): 1-24, Transmitter delay 0, non-inverted data
2811:
Serial0/1/1:0 is down, line protocol is down
Hardware is GT96K Serial
MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec,
reliability 252/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
CRC checking enabled
Last input 18:33:23, output 18:33:13, output hang never
Last clearing of "show interface" counters 19:36:46
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 1152 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
39 packets input, 3582 bytes, 0 no buffer
Received 39 broadcasts, 0 runts, 1 giants, 0 throttles
16 input errors, 16 CRC, 14 frame, 6 overrun, 0 ignored, 8 abort
40 packets output, 3606 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 output buffer failures, 0 output buffers swapped out
2 carrier transitions
Timeslot(s) Used:1-24, SCC: 1, Transmitter delay is 0 flags
Both are configured only with an IP and are unshut.
Thanks
Justin
_______________________________________________
cisco-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
