Hi Farhan, Yes I did follow all steps and box is up and running 4.0.1 w/o any issue. Also it has Fat32 partition.
Regards, Vikas On Fri, Feb 25, 2011 at 5:04 PM, Farhan Jaffer <[email protected]> wrote: > Hi Vikas, > > Have the CRS is running on 4.0.1? I mean that the all steps required to > complete the installation have completed? Or you are stuck during > installation... > For downgrade the same procedures are required. However your flash file > system is required to up-grade from FAT 16 to FAT 32 in 4.0.1, have you did > this? > > -FJ > > On Fri, Feb 25, 2011 at 4:05 PM, Vikas Sharma <[email protected]>wrote: > >> Also I can see this log which clearly says no upgrade package is >> available >> but then why it asks to uninstall the upgrade package.. >> >> Fri Feb 25 02:26:03.572 UTC >> Install operation 396 '(admin) install remove >> disk1:hfr-upgrade-p.pie-4.0.1 >> synchronous' started by user 'colt123' via CLI at 02:26:04 UTC Fri Feb 25 >> 2011. >> P/0/RP0/CPU0:Feb 25 02:26:04.876 : instdir[216]: >> %INSTALL-INSTMGR-3-INSTALL_OPERATION_USER_ERROR : User error occurred >> during >> install operation 396. See 'show install log 396 detail' for more >> inKformation. >> Warning: The following specified package does not use the boot device, >> and >> so >> Warning: will not be removed: >> Warning: disk1:hfr-upgrade-p.pie-4.0.1 >> Error: There are no valid packages on the boot device to be removed. >> >> Regards, >> VIkas >> >> On Fri, Feb 25, 2011 at 4:33 PM, Vikas Sharma <[email protected] >> >wrote: >> >> > Hi, >> > >> > I have upgraded CRS1 to 4.0.1 from 3.6.2. Upgrade worked fine and it is >> > running 4.0.1. But the issue is I am not able to downgrade it back to >> 3.6.2 >> > >> > If I am trying to run any install command I see similar output - >> > >> > RP/0/RP0/CPU0:crs1.BLB(admin)#install commit >> > Fri Feb 25 03:45:10.181 UTC >> > Install operation 402 '(admin) install commit' started by user 'colt123' >> > via >> > CLI at 03:45:10 UTC Fri Feb 25 2011. >> > Error: Cannot proceed with the operation because the upgrade package >> is >> > Error: active. >> > Error: >> > Error: The package should only be used when upgrading from software >> > RP/0/RP0/CPU0:Feb 25 03:45:11.503 : instdir[216]: >> > %INSTALL-INSTMGR-3-INSTALL_OPERATION_USER_ERROR : User error occurred >> during >> > install operation 402. See 'show install log 402 detail' for more >> > inError: versions prior to 4.0.0. Once the upgrade is complete, it >> should >> > be >> > formation. >> > Error: immediately deactivated and removed. No further install >> > operations >> > Error: will be allowed until this is completed. >> > Error: >> > Error: Deactivate the package from the entire router by executing >> the >> > Error: 'install deactivate ' command in admin mode. >> > Error: Remove the package from the entire router by executing the >> > 'install >> > Error: remove ' command in admin mode. >> > Error: No further install operations will be allowed until this is >> > Error: completed. >> > Install operation 402 failed at 03:45:11 UTC Fri Feb 25 2011. >> > I have also checked on the active and inactive files and could not >> locate >> > upgrade package on active disk (boot disk). Does anyone has faced >> similar >> > issue? >> > >> > Regards, >> > Vikas >> > >> _______________________________________________ >> cisco-nsp mailing list [email protected] >> https://puck.nether.net/mailman/listinfo/cisco-nsp >> archive at http://puck.nether.net/pipermail/cisco-nsp/ >> > > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
