Martin,
Yes, you right, my mistake, we are using C3KX-NM-10G, and at time when
we bough it there no C3KX-NM-10GT modules, so I automatically think them.
You probably won't able to do so, because we even had problems with size
of regular SFP(not rj45) on C3KX-NM-10G, so we had to replace them from
different company. And from what I see sfp on 3750X-24S-S sit to each
other very closely same as on C3KX-NM-10G.
Can't say anything about 4900 series.
On 02.10.2011 5:33, Martin T wrote:
Nikolay,
I'm afraid you are confusing this with C3KX-NM-10G module. Check the
table 3. C3KX-NM-10GT module is strictly 2x 10GBASE-T RJ45 ports(image
of the C3KX-NM-10GT: http://mcaf.ee/0bjty).
In general, "WS-C3750X-24S-S + C3KX-NM-10GT" seems to be a perfect
solution. WS-C3750X-24S-S has an "IP Base" image, which is enough
because I don't need advanced L3 features like EIGRP, OSPF, BGP and
IPv6 routing provided by "IP Services". WS-C3750X-24S-S is easily
upgradable thanks to StackWise Plus and StackPower technologies.
Supports dual redundant power supplies and in overall is a nice 1U
feature-rich switch according to specifications.
Just one hesitation with WS-C3750X-24S-S..is it possible to insert
1000BASE-T SFP's to first 22 ports(I would use last two SFP ports for
1000BASE-LX10 SFP's)? I mean 1000BASE-T SFP's have RJ45 connector
which is bit bulky and I'm not sure if it's possible to physically
insert 1000BASE-LX10 SFP's besides each other? Any experience with
this?
In addition, as I checked the 4900 series as well, do built in X2
ports(the ones in the chassis http://mcaf.ee/us1dt) in 4900M support
"TwinGig Converter Module"? According to documentation they don't. Any
experience with this?
regards,
martin
2011/10/1 Nikolay Shopik<[email protected]>:
Martin,
C3KX-NM-10GT allow you to install only two 10Gb SFP+ or 4 1Gbit SFP, or just
ony 10Gbit SFP+ plus 2 1Gbit SFP. You can take look here
http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps6406/data_sheet_c78-584733.html
at table 4.
On 30.09.2011 23:44, Martin T wrote:
Alan, Arne:
WS-C3750X-24S-E + C3KX-NM-10GT seems to be a perfect solution!
WS-C3750X-24S-E has 24 SFP ports so one could use 12 1000BASE-T SFP's
+ 2 1000BASTE-LX10 SFP's and C3KX-NM-10GT module provides two
10GBASE-T ports so all the requirements seems to be fulfilled.
Jim,
I'm afraid WS-C4928-10GE would not suite because two 10GBASE-T ports
are must-have. If there would be 10GBASE-T X2 modules available, this
switch would be a nice option.
Kevin,
if possible, I would prefer Cisco.
What do you think about "WS-C3750X-24S-E + C3KX-NM-10GT" solution? In
addition, are there 10GBASE-T SFP+ modules available on the
market(Cisco or third-party)?
regards,
martin
2011/9/30 Kevin Loch<[email protected]>:
Martin T wrote:
Is there a Cisco switch(non-modular preferably) which fulfils those
requirements:
1) 12 or more 1000BASE-T ports
2) 2x SFP port for 1000BASE-LX10 SFP's
3) 2x 10GBASE-T ports(for IBM 10Gb iSCSI Host Interface Card 81Y9613,
which has two 10GBASE-T interfaces)
It's not Cisco but Dell 6248 does have a 2 port 10Gbase-T module
option. The onboard SFP ports will accept any generic 1G SFP's
(for your LX10 optics).
- Kevin
_______________________________________________
cisco-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
_______________________________________________
cisco-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
_______________________________________________
cisco-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
