Vlan 100 Name myvlanname Is missing
Sent from a mobile device On 22/02/2013, at 8:45, Kevin Berry <[email protected]> wrote: > ok, hopefully this answers some things. > I have logged a few commands. I have a show of the etherchannel, po1. I have > a show of STP, of vlans, and also a show of switchport. I only did that for > gi 0/1 (have a blade there) and of an uplink port gi 0/20 and of the port > channel po1. LEt me know what you guys think......I'm running out of time! > Thanks so much for all your help! > > Attached is Cisco commands showing alot. > > > Also, here is the switch on the other end showing vlans > > vlan 1 > name "DEFAULT_VLAN" > untagged 1,3,5,7,9,11,13,15,17-20,23-36,39-48,Trk1-Trk2 > ip address 10.10.0.13 255.255.0.0 > no untagged 2,4,6,8,10,12,14,16 > ip igmp > exit > vlan 2 > name "192_DMZ" > untagged 2,4,6,8,10,12,14,16 > tagged Trk1-Trk2 > exit > vlan 3 > name "VLAN3" > tagged Trk1-Trk2 > exit > vlan 100 > name "VLAN100" > tagged Trk1-Trk2 > exit > > On Thu, Feb 21, 2013 at 3:25 PM, Matlock, Kenneth L > <[email protected]> wrote: >> 1) Is VLAN3 in STP forwarding state on Gi0/1, Gi0/2, and wherever the root >> port is? >> 2) Is VLAN3 defined on the device on the other end of Portchannel1? >> >> >> Ken Matlock >> Network Engineer >> 303-467-4671 >> [email protected] >> >> >> >> >> -----Original Message----- >> From: Kevin Berry [mailto:[email protected]] >> Sent: Thursday, February 21, 2013 11:41 AM >> To: 'Peter Rathlev'; Andrew Miehs; Matlock, Kenneth L >> Cc: 'cisco-nsp' >> Subject: RE: [c-nsp] FW: Cisco blade switch config >> >> Corrected this. Now gi 0/1 - 3 show up/up. My uplinks, gi 0/20 & 0/22 are >> also up/up. >> >> I can now ping the root switch from this switch on VLAN 1 (10.10.0.x) and >> VLAN 2 (192.168.1.x), but NOT VLAN 3 (172.18.132.x). This occurs over an >> etherchannel link that includes these 3 vlans. >> >> This is the case for both of my Cisco switches in this enclosure (redundant) >> talking back to my HP root. Checked the HP. The trunks are tagged for all of >> those vlans. From the HP, I can ping out to servers on all of those vlans >> without a hitch. >> >> >> >> >> -----Original Message----- >> From: Peter Rathlev [mailto:[email protected]] >> Sent: Thursday, February 21, 2013 12:59 PM >> To: Kevin Berry >> Cc: cisco-nsp >> Subject: Re: [c-nsp] FW: Cisco blade switch config >> >> On Thu, 2013-02-21 at 09:25 -0500, Kevin Berry wrote: >> > Now, the show inter trunk: >> ... >> > WHY is it that gi 0/1 & gi 0/2 are not here? I have hosts in those >> > slots, powered on, and need to be on VLANs 1,2,3, 100. >> >> Maybe they're down. The "operational mode" of "show interface Gi0/{1,2} >> switchport" should tell you what the port is like. >> >> -- >> Peter > > <cisco-sw2.TXT> _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
