Read what Claes said. You must change SDM to applications.
Fredrik Vöcks Senior IP Network Engineer On 23 May 2013 15:09, PlaWanSai <[email protected]> wrote: > I enabled on loopback 0. And I see this log on first boot: > > 000038: *May 22 16:28:50.879 BKK: NQATM: > 000039: *May 22 16:28:50.879 BKK: nqatm_add_mdt_tcam_entry:Failed allocate > tcam hw handle > 000040: *May 22 16:28:50.879 BKK: NQATM: > 000041: *May 22 16:28:50.879 BKK: nqatm_add_mdt_tcam_entry:Failed allocate > tcam hw handle > 000042: *May 22 16:28:50.879 BKK: NQATM: > 000043: *May 22 16:28:50.879 BKK: nqatm_add_mdt_tcam_entry:Failed allocate > tcam hw handle > 000044: *May 22 16:28:50.879 BKK: NQATM: > 000045: *May 22 16:28:50.879 BKK: nqatm_add_mdt_tcam_entry:Failed allocate > tcam hw handle > 000046: *May 22 16:28:50.879 BKK: NQATM: > 000047: *May 22 16:28:50.879 BKK: nqatm_add_mdt_tcam_entry:Failed allocate > tcam hw handle > 000048: *May 22 16:28:50.879 BKK: NQATM: > 000049: *May 22 16:28:50.879 BKK: nqatm_add_mdt_tcam_entry:Failed allocate > tcam hw handle > 000050: *May 22 16:28:50.879 BKK: NQATM: > 000051: *May 22 16:28:50.879 BKK: nqatm_add_mdt_tcam_entry:Failed allocate > tcam hw handle > 000052: *May 22 16:28:50.879 BKK: NQATM: > 000053: *May 22 16:28:50.879 BKK: nqatm_add_mdt_tcam_entry:Failed allocate > tcam hw handle > 000054: *May 22 16:28:50.879 BKK: NQATM: > 000055: *May 22 16:28:50.879 BKK: nqatm_add_mdt_tcam_entry:Failed allocate > tcam hw handle > 000056: *May 22 16:28:50.879 BKK: NQATM: > 000057: *May 22 16:28:50.879 BKK: nqatm_add_mdt_tcam_entry:Failed allocate > tcam hw handle > > Thank you very much. > > -----Original Message----- > From: Claes Jansson [mailto:[email protected]] > Sent: Thursday, May 23, 2013 7:34 PM > To: PlaWanSai > Cc: [email protected] > Subject: Re: [c-nsp] ME-3600 Can't see ip pim vrf neighbor > > Also be sure to use > > ip pim ssm default > > and > > sdm prefer applications > > By default "MDT mroutes" are 0... > > I have tested this on 15.3(2)S. > > Claes Jansson > Gästabudstaden AB > > On 2013-05-23 08:38, PlaWanSai wrote: > > I try to run Multicast VPN on the ME-3600 back-to-back with the 7609. > > It does not see pim neighbor. I tested on 15.1(2)EY4, 15.3(1)S and > > 15.3(2)S IOS version. I used this configuration between 7609 is work. > > > > > > > > test-co3600#sho ip pim vrf IPTV-M nei > > > > PIM Neighbor Table > > > > Mode: B - Bidir Capable, DR - Designated Router, N - Default DR > > Priority, > > > > P - Proxy Capable, S - State Refresh Capable, G - GenID Capable > > > > Neighbor Interface Uptime/Expires Ver DR > > > > Address > Prio/Mode > > > > test-co3600# > > > > > > > > Thank you very much. > > > > _______________________________________________ > > cisco-nsp mailing list [email protected] > > https://puck.nether.net/mailman/listinfo/cisco-nsp > > archive at http://puck.nether.net/pipermail/cisco-nsp/ > > > > > > > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
