The voice over IP depends on the IP portion of the network working - just set
up the routers as you normally would and the voice traffic will travel just fine.
You do have a potential problem with congestion here, don't you? I am assuming
more than one type of data is using the area of the network that has the 4500s in
it.
This will be a good chance to exercise your cisco skills? Will IP precedence on
the 1750s do the job? Do you have to set up the 4500s to handle precedence as
well? Perhaps its a job for customer/priority queueing??
You'll have a wonderful learning experience with this ...
Janto Cin wrote:
> On Mon, 17 Jul 2000, you wrote:
>
> thanks for the attention,
> correction for network layout :
>
> x25 LL FR x25
> POTS1 ---- 1750 ---- 4500 ---- 4500 ---- 4500 ---- 1750 ---- POTS2
>
> can I configure the voice connection between both POTS but still use x25 for
> data ? how to configure the routers ?
> thanks.
> Janto
>
> > If you just want to 'bridge' analog phone service this is what you need
> > - private line automatic ringdown (plar) means that the connection is
> > established as soon as one end goes off the hook. This is a point to
> > point config ... if you want to get fancier than this you need to create
> > a dial plan.
> >
> > --- router one ---
> >
> > voice-port 1/0/0
> > connection plar 194
> > !
> > !
> > dial-peer voice 194 voip
> > destination-pattern 194
> > codec g711ulaw
> > session target ipv4:x.x.x.241
> > !
> > !
> > dial-peer voice 1 pots
> > destination-pattern 167
> > port 1/0/0
> >
> > --- router two ---
> > voice-port 1/0/0
> > connection plar 167
> > !
> > dial-peer voice 167 voip
> > destination-pattern 167
> > codec g711ulaw
> > session target ipv4:x.x.x.245
> >
> > dial-peer voice 1 pots
> > destination-pattern 194
> > port 1/0/0
> >
> >
> > [EMAIL PROTECTED] wrote:
> >
> > > hi all,
> > >
> > > here's the network layout
> > >
> > > x25 LL
> > > FR x25
> > > POTS 1 --- 1750 ------ 4500 ------ 4500 ------- 4500 ----------- 1750
> > > ---- POTS 2
> > >
> > > how to setup the router for voice connection from both POTS ?
> > > thank you very much.
> > >
> > > Best Regards,
> > > JC
> > >
> > > ___________________________________
> > > UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
> > > FAQ, list archives, and subscription info: http://www.groupstudy.com
> > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
> --
> Best Regards,
> Janto Cin
> PT Datacomm Diangraha
> Phone : 62-21-6303030 (Hunting)
> Mobile : 62-812-9102542
>
> ___________________________________
> UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
> FAQ, list archives, and subscription info: http://www.groupstudy.com
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
___________________________________
UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
FAQ, list archives, and subscription info: http://www.groupstudy.com
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
