Dave,
It _used_ to be that way, I think. I went to CCO and couldn't find the page that used
to say that. Oh well, I'll chalk it up to my having had another "senior moment." I
knew I shouldn't have stopped eating those blueberries!! :)
Tom Lisa, Instructor, CCNA, CCAI
Community College of Southern Nevada
Cisco Regional Networking Academy
[EMAIL PROTECTED] wrote:
> Tom,
>
> Actually, I did not have to do that. I just TFTPed the 9.00.04 EN code
> right in on top of the 8.01.00 code and it came back up with VLAN support
> (after turning off bridge-group mode).
>
> Dave Goldsmith
>
> -----Original Message-----
> From: Tom Lisa [mailto:[EMAIL PROTECTED]]
> Sent: Tuesday, February 06, 2001 3:06 PM
> To: [EMAIL PROTECTED]
> Cc: [EMAIL PROTECTED]
> Subject: Re: VLANs on Catalyst 1900 Switches
>
> Dave,
>
> Don't forget, before you put 9.00.04 Enterprise on you must upgrade the
> 8.01.00 Standard
> to 9.00.04 Standard then make the conversion to Enterprise version. I have
> been meaning
> to research why you must upgrade to latest standard before you can put on
> enterprise (if
> you don't already have enterprise on that is) but haven't found out yet.
> Perhaps
> someone else on the list knows.
>
> Tom Lisa, Instructor, CCNA, CCAI
> Community College of Southern Nevada
> Cisco Regional Networking Academy
>
> [EMAIL PROTECTED] wrote:
>
> > Tom,
> >
> > That was it. The Cat1900 with the 9.00.04 Enterprise edition s/w now has
> > the vlan options available now. The Cat1900 with the 8.01.00 s/w does
> not.
> > The Cat1900s used in the CCNA course my coworker just took had 8.01.07
> > loaded so 8.01.00 may not support VLANs ... I'll just put the 9.00.04 code
> > on it.
> >
> > Thanks,
> >
> > Dave Goldsmith
> >
> > -----Original Message-----
> > From: Tom Lisa [mailto:[EMAIL PROTECTED]]
> > Sent: Monday, February 05, 2001 8:10 PM
> > To: [EMAIL PROTECTED]
> > Cc: [EMAIL PROTECTED]
> > Subject: Re: VLANs on Catalyst 1900 Switches
> >
> > Dave,
> >
> > It sounds like your switches are configured for bridge groups rather than
> > VLANS. This
> > can be reset by going to the Main Menu and selecting S (System Sub-Menu).
> > Then select
> > option T (Reset to VLANS) to enable VLAN configuration. Option T changes
> to
> > Reset to
> > Bridge Groups when VLANS are enabled.
> >
> > HTH,
> > Tom Lisa, Instructor, CCNA, CCAI
> > Community College of Southern Nevada
> > Cisco Regional Networking Academy
> >
> > [EMAIL PROTECTED] wrote:
> >
> > > I have 2 Cat1900 switches (WS-1912-A). One has the 8.01.00 Standard
> > Edition
> > > loaded and the other has the 9.00.04 Enterprise Edition loaded. On
> > neither
> > > of them are any of the VLAN commands available.
> > >
> > > The Cisco ICND book covers VLANs on Cat1900 switches and a co-worker
> just
> > > attended a GlobalKnowledge CCNA Boot Camp where they did configure VLANs
> > on
> > > Cat1900s (with version 8.xx loaded).
> > >
> > > In addition to the software version, is there a hardware issue? Do some
> > > Cat1900s not support VLANs?
> > >
> > > Dave Goldsmith
> >
> > _________________________________
> > FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
>
> _________________________________
> FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
_________________________________
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
