Cisco People I need you help...
I would appreciate any help. I have a 6500Cat running Redundant Supervisor
engines and two MSFC installed one on each supervisor engine.
*****
Mod Slot Ports Module-Type Model Sub Status
--- ---- ----- ------------------------- ------------------- --- --------
1 1 2 1000BaseX Supervisor WS-X6K-SUP2-2GE yes ok
15 1 1 Multilayer Switch Feature WS-F6K-MSFC2 no ok
2 2 2 1000BaseX Supervisor WS-X6K-SUP2-2GE yes standby
16 2 1 Multilayer Switch Feature WS-F6K-MSFC2 no ok
3 3 8 1000BaseX Ethernet WS-X6408A-GBIC no ok
4 4 8 1000BaseX Ethernet WS-X6408A-GBIC no ok
6 6 48 10/100BaseTX Ethernet WS-X6348-RJ-45 no ok
7 7 48 10/100BaseTX Ethernet WS-X6348-RJ-45 no ok
8 8 48 10/100BaseTX Ethernet WS-X6348-RJ-45 no ok
9 9 48 10/100BaseTX Ethernet WS-X6348-RJ-45 no ok
*****
I created one vlan (Vlan 20) and I want to use HSRP across the MSFC so the
clients can have a steady Gateway.
Default vlan 1 works fine, I can ping accross to the other MSFC. But
Vlan20 the one I created on the switch does give me connectivity accoss
MFSC.
MSFC#1
interface Vlan20
ip address 10.224.173.3 255.255.255.0
no ip redirects
ip route-cache flow
standby priority 80 preempt
standby authentication XXXX
standby ip 10.224.173.1
MSFC#2
interface Vlan20
mac-address 0012.3456.7891
ip address 10.224.173.2 255.255.255.0
no ip redirects
ip route-cache flow
standby priority 90 preempt
standby authentication XXXX
standby ip 10.224.173.1
********
Test-6500-MSFC2#ping 10.224.173.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.224.173.1, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
Test-6500-MSFC2#
------
******
On the switch trunks shows this...
Test-6500> (enable) show trunk
* - indicates vtp domain mismatch
Port Mode Encapsulation Status Native vlan
-------- ----------- ------------- ------------ -----------
15/1 nonegotiate isl trunking 1
16/1 nonegotiate isl trunking 1
Port Vlans allowed on trunk
--------
---------------------------------------------------------------------
15/1 1-1005,1025-4094
16/1 1-1005,1025-4094
Port Vlans allowed and active in management domain
--------
---------------------------------------------------------------------
15/1 1 (enable)
**********
Show Vlan
VLAN Name Status IfIndex Mod/Ports, Vlans
---- -------------------------------- --------- -------
------------------------
1 default active 199 1/1-2
2/1-2
20 TEST-VLAN active 208
30 VLAN30 active 207
999 Dead-Vlan active 225 3/1-8
4/1-8
6/1-48
7/1-48
8/1-48
9/1-48
1002 fddi-default active 200
1003 token-ring-default active 203
1004 fddinet-default active 201
1005 trnet-default active 202
***********************************************************************
Question 1.-----
Why isn't vlan 20 and 30 and 999 in the Management domain? (Above Show
trunk command)
Question 2.-----
Becuase Vlan 20 and 30 aren't in the Management domain, Is this the reason
why I am getting no Msfc connectivity for those Vlans..
Sorry for the long letter, appreciate any info you have..
Regards,
Eric
_________________________________________________________________
$B$+$o$$$$(B & $B;H$($k%V%i%&%6$G!"%$%s%?!<%M%C%H@83h$b$C$H3Z$7$/$J$k!*(B
http://explorer.msn.co.jp/
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=23744&t=23744
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
