He doesn't need to trunk between switches, this is a single switch with two MSFC's. Your HSRP looks fine but are the interfaces up?? If you have no switch ports active in the designated VLANs the MSFC VLAN will not come active.
The management VLAN stuff is VTP, nothing to do with your problem. Do a sh stand vlan x, see what state they ae in. Dave Brant Stevens wrote: > > Are you trunking on any other ports? You need to trunk between switches if > you want routing amongst multiple VLANs to become redundant via the MSFCs... > > ----- Original Message ----- > From: "Washington Rico" > To: > Sent: Monday, October 22, 2001 12:10 AM > Subject: Intervlan Connectivity is not working? [7:23744] > > > Cisco People I need you help... > > > > I would appreciate any help. I have a 6500Cat running Redundant > Supervisor > > engines and two MSFC installed one on each supervisor engine. > > ***** > > Mod Slot Ports Module-Type Model Sub Status > > --- ---- ----- ------------------------- ------------------- --- -------- > > 1 1 2 1000BaseX Supervisor WS-X6K-SUP2-2GE yes ok > > 15 1 1 Multilayer Switch Feature WS-F6K-MSFC2 no ok > > 2 2 2 1000BaseX Supervisor WS-X6K-SUP2-2GE yes standby > > 16 2 1 Multilayer Switch Feature WS-F6K-MSFC2 no ok > > 3 3 8 1000BaseX Ethernet WS-X6408A-GBIC no ok > > 4 4 8 1000BaseX Ethernet WS-X6408A-GBIC no ok > > 6 6 48 10/100BaseTX Ethernet WS-X6348-RJ-45 no ok > > 7 7 48 10/100BaseTX Ethernet WS-X6348-RJ-45 no ok > > 8 8 48 10/100BaseTX Ethernet WS-X6348-RJ-45 no ok > > 9 9 48 10/100BaseTX Ethernet WS-X6348-RJ-45 no ok > > ***** > > > > I created one vlan (Vlan 20) and I want to use HSRP across the MSFC so the > > clients can have a steady Gateway. > > > > Default vlan 1 works fine, I can ping accross to the other MSFC. But > > Vlan20 the one I created on the switch does give me connectivity accoss > > MFSC. > > MSFC#1 > > interface Vlan20 > > ip address 10.224.173.3 255.255.255.0 > > no ip redirects > > ip route-cache flow > > standby priority 80 preempt > > standby authentication XXXX > > standby ip 10.224.173.1 > > MSFC#2 > > interface Vlan20 > > mac-address 0012.3456.7891 > > ip address 10.224.173.2 255.255.255.0 > > no ip redirects > > ip route-cache flow > > standby priority 90 preempt > > standby authentication XXXX > > standby ip 10.224.173.1 > > ******** > > Test-6500-MSFC2#ping 10.224.173.1 > > > > Type escape sequence to abort. > > Sending 5, 100-byte ICMP Echos to 10.224.173.1, timeout is 2 seconds: > > ..... > > Success rate is 0 percent (0/5) > > Test-6500-MSFC2# > > ------ > > ****** > > On the switch trunks shows this... > > > > Test-6500> (enable) show trunk > > * - indicates vtp domain mismatch > > Port Mode Encapsulation Status Native vlan > > -------- ----------- ------------- ------------ ----------- > > 15/1 nonegotiate isl trunking 1 > > 16/1 nonegotiate isl trunking 1 > > > > Port Vlans allowed on trunk > > -------- > > --------------------------------------------------------------------- > > 15/1 1-1005,1025-4094 > > 16/1 1-1005,1025-4094 > > > > Port Vlans allowed and active in management domain > > -------- > > --------------------------------------------------------------------- > > 15/1 1 (enable) > > > > ********** > > Show Vlan > > VLAN Name Status IfIndex Mod/Ports, Vlans > > ---- -------------------------------- --------- ------- > > ------------------------ > > 1 default active 199 1/1-2 > > 2/1-2 > > 20 TEST-VLAN active 208 > > 30 VLAN30 active 207 > > 999 Dead-Vlan active 225 3/1-8 > > 4/1-8 > > 6/1-48 > > 7/1-48 > > 8/1-48 > > 9/1-48 > > 1002 fddi-default active 200 > > 1003 token-ring-default active 203 > > 1004 fddinet-default active 201 > > 1005 trnet-default active 202 > > *********************************************************************** > > > > Question 1.----- > > Why isn't vlan 20 and 30 and 999 in the Management domain? (Above Show > > trunk command) > > Question 2.----- > > Becuase Vlan 20 and 30 aren't in the Management domain, Is this the reason > > why I am getting no Msfc connectivity for those Vlans.. > > > > > > Sorry for the long letter, appreciate any info you have.. > > > > Regards, > > Eric > > > > > > > > _________________________________________________________________ > > $B$+$o$$$$(B & > $B;H$($k%V%i%&%6$G!"%$%s%?! http://explorer.msn.co.jp/ -- David Madland Sr. Network Engineer CCIE# 2016 Qwest Communications Int. Inc. [EMAIL PROTECTED] 612-664-3367 "Emotion should reflect reason not guide it" Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=23791&t=23744 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
