let me know the shipping cost I will send you a check out today.
On 11/21/13, Curtis <cpt.b...@gmail.com> wrote: > Please send it to > > Lavan McDaniel > 46 bostick cir Beaufort, SC. > 29902 > > Thanks so much. > > > On 11/21/13, Neil Andersen <neil.eric.ander...@gmail.com> wrote: >> Still available? Be very glad to have it. Just let me know the >> particulars. >> >> Neil Andersen >> 1982 C&C 32, FoxFire >> Worton Creek, MD >> >> On Thu, Nov 21, 2013 at 9:01 AM, Gary Nylander >> <gnylan...@atlanticbb.net>wrote: >> >>> I have a Datamarine Link 5100 system - appears to be complete. Came >>> from >>> my SO's late sister - must have been taken out before they upgraded and >>> embarked on a voyage south. >>> >>> Datamarine 5100 control head, Display unit with digital speed and depth, >>> analog wind; DX111 depth, SX 120 speed, wind speed/direction mast top >>> unit, >>> coax cable, through hull speed and depth sensors.... >>> >>> Yours for the cost of shipping, I have no need. >>> >>> Gary Nylander >>> Maryland >>> >>> >>> >>> ----- Original Message ----- >>> *From:* Robert Abbott <robertabb...@eastlink.ca> >>> *To:* cnc-list@cnc-list.com >>> *Sent:* Wednesday, November 20, 2013 9:13 AM >>> *Subject:* Stus-List Muffler >>> >>> John: >>> >>> I replaced the SS muffler this past Spring.....don't remember the exact >>> measurements put similar to yours. >>> >>> I replaced it with a Vernalift resin muffler....slightly bigger (2" >>> higher) muffler but with the same 2" inlet and 1 1/2" outlet. I will >>> try >>> to find my receipt which will have the part # if that helps you. Bottom >>> line, Vernalift makes a resin muffler with a 1/1/2" outlet. I didn't >>> want >>> to get into adding hose adapters as my exhaust hoes was replaced last >>> year >>> and it is 1 1/2". There are no back pressure issues to worry about with >>> the 1 1/2" outlet with these small marine diesel engines. >>> >>> Bob Abbott >>> AZURA >>> C&C 32 - 84 >>> Halifax, N.S. >>> >>> >>> >>> >>> >>> >>> >>> >>> On 2013/11/20 9:00 AM, John and Maryann Read wrote: >>> >>> The stainless muffler has finally given up the ghost. It is 6 ¼ round, >>> 2 inch side inlet and 1 ½ inch top outlet, 9 inches high and the base is >>> 7 >>> inches square. Any suggested sources?? Vernalift by Centek Industries >>> makes a close copy but the outlet is 2 inch. On a related note, any >>> thoughts on why the outlet is smaller than the inlet and does this >>> create >>> any backpressure issues?? The engine outlet is 2 inch. On the other >>> hand, >>> this set up has worked well for 30 years so it can’t be all bad J >>> >>> TIA >>> >>> John and Maryann >>> >>> Legacy III >>> >>> 1982 C&C 34 >>> >>> Noank, CT >>> >>> >>> >>> _______________________________________________ >>> This List is provided by the C&C Photo >>> Albumhttp://www.cncphotoalbum.comcnc-l...@cnc-list.com >>> >>> >>> ------------------------------ >>> >>> _______________________________________________ >>> This List is provided by the C&C Photo Album >>> http://www.cncphotoalbum.com >>> CnC-List@cnc-list.com >>> >>> >>> _______________________________________________ >>> This List is provided by the C&C Photo Album >>> http://www.cncphotoalbum.com >>> CnC-List@cnc-list.com >>> >>> >> > > > -- > “Sailors, with their built in sense of order, service and discipline, > should really be running the world.” - Nicholas Monsarrat > -- “Sailors, with their built in sense of order, service and discipline, should really be running the world.” - Nicholas Monsarrat _______________________________________________ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com
