I have not tried this but a friend repainted his waterline stipe and used electrical tape, apparently it follows curves etc. easily
Tim C&C 33mkii Matico From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Dave Godwin via CnC-List Sent: Tuesday, September 20, 2016 11:10 AM To: cnc-list@cnc-list.com Cc: Dave Godwin <dave.god...@me.com> Subject: Re: Stus-List Repainting Waterline Stripe... What Andy said. I use 3/4” tape and it works (curves..) just fine. Dave Godwin 1982 C&C 37 - Ronin Reedville - Chesapeake Bay Ronin’s Overdue Refit<http://roninrebuild.blogspot.com/> On Sep 20, 2016, at 11:05 AM, Andrew Burton via CnC-List <cnc-list@cnc-list.com<mailto:cnc-list@cnc-list.com>> wrote: David, I use Fine Line tape on my models making the same curves only at 1/2" to the foot! You should be able to make 3/4" tape go around the bends at full scale. Andy C&C 40 Peregrine On Tue, Sep 20, 2016 at 11:01 AM, David via CnC-List <cnc-list@cnc-list.com<mailto:cnc-list@cnc-list.com>> wrote: My biggest concern is flexibility at the aft end where the strips starts curving radically. 1/4" painters tape is flexible? Thanks in advance David F. Risch (401) 419-4650<tel:%28401%29%20419-4650> (cell) ________________________________ To: cnc-list@cnc-list.com<mailto:cnc-list@cnc-list.com> Date: Tue, 20 Sep 2016 14:50:57 +0000 Subject: Re: Stus-List Repainting Waterline Stripe... From: cnc-list@cnc-list.com<mailto:cnc-list@cnc-list.com> CC: mike.h...@impgroup.com<mailto:mike.h...@impgroup.com> You can get painter masking tape as think as ¼ inch. Use that for the contoured areas and then put something wider overlapping over that. Has always worked for me when painting decks, etc … From: CnC-List [mailto:cnc-list-boun...@cnc-list.com<mailto:cnc-list-boun...@cnc-list.com>] On Behalf Of Dave Godwin via CnC-List Sent: Tuesday, September 20, 2016 11:45 AM To: cnc-list@cnc-list.com<mailto:cnc-list@cnc-list.com> Cc: Dave Godwin Subject: Re: Stus-List Repainting Waterline Stripe... David, I’d spend the few extra bucks and get a good 3M tape. I just did some Awlcraft painting for gloss and non-skid on my hatches and I used the Awlgrip (and my painter) recommended 3M 218 Fine Line tape for masking the gloss vs. non-skid prior to spraying. I’ll be masking off the entire deck sometime this week or next and I find the 218 properties to be easy to use. Electrical tape is a bit stretchy and I’m not fond of the glue used. Don’t know what your setup with the boat in the yard is but a good way to mark the waterline and boot stripes is with a laser. Boat’s gotta be level fore-and-aft and side-to-side. Best, Dave Godwin 1982 C&C 37 - Ronin Reedville - Chesapeake Bay Ronin’s Overdue Refit<http://roninrebuild.blogspot.com/> On Sep 20, 2016, at 10:03 AM, Joel Aronson via CnC-List <cnc-list@cnc-list.com<mailto:cnc-list@cnc-list.com>> wrote: David, I would check with the manufacturer to see what you can use over AwlGrip. On Tue, Sep 20, 2016 at 9:59 AM, David via CnC-List <cnc-list@cnc-list.com<mailto:cnc-list@cnc-list.com>> wrote: Neil, You are the man...as my next question was how to follow the extreme curvature under the stern (waterline and curves widens radically to maintain visual width when hull tucks under). This is my solution. Thanks! David F. Risch (401) 419-4650 (cell) ________________________________ _______________________________________________ This list is supported by the generous donations of our members. If you like what we do, please help us pay for our costs by donating. All Contributions are greatly appreciated! _______________________________________________ This list is supported by the generous donations of our members. If you like what we do, please help us pay for our costs by donating. All Contributions are greatly appreciated! -- Andrew Burton 61 W Narragansett Ave Newport, RI USA 02840 http://sites.google.com/site/andrewburtonyachtservices/ phone +401 965 5260 _______________________________________________ This list is supported by the generous donations of our members. If you like what we do, please help us pay for our costs by donating. All Contributions are greatly appreciated! ________________________________ This communication is confidential. We only send and receive email on the basis of the terms set out at www.rogers.com/web/content/emailnotice<http://www.rogers.com/web/content/emailnotice> Ce message est confidentiel. Notre transmission et réception de courriels se fait strictement suivant les modalités énoncées dans l’avis publié à www.rogers.com/aviscourriel <http://www.rogers.com/aviscourriel> ________________________________
_______________________________________________ This list is supported by the generous donations of our members. If you like what we do, please help us pay for our costs by donating. All Contributions are greatly appreciated!