Alright so here is what I see. You have you are trying to setup your dhcpd on a virtual interface and not a real interface. That will not work, you need ARP to have dhcpd working. Look at this:
http://forum.openvz.org/index.php?t=msg&goto=33837&; This will help you likely. Basically what your dhcp server is trying to do is run not on venet0:0 but on venet0 for which you do not have subnet defined. You likely can test that by defining the subnet of your vnet0. It may startup for you (but obviously won't do anything useful). You will likely have to create a bridged interface and put that. I suppose you can try to include the venet0 subnet in your dhcpd.conf and it may work, I never tested it that way, but it be worth a shot just to see. Marek Dohojda 720-308-8622 77 68 6f 20 69 73 20 4a 6f 68 6e 20 47 61 6c 74 3f 0d 0a -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Frank Sent: Tuesday, July 12, 2011 12:59 PM To: cobbler mailing list Subject: RE: *paid install help?*: Cobbler on a OpenVZ container / "dhcpd" failing > /etc/sysconfig/dhcpd # Command line options here DHCPDARGS= >your ifconfig printout [root@cobbler sysconfig]# ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:20670 errors:0 dropped:0 overruns:0 frame:0 TX packets:20670 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2331576 (2.2 MiB) TX bytes:2331576 (2.2 MiB) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:127.0.0.1 P-t-P:127.0.0.1 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:18501 errors:0 dropped:0 overruns:0 frame:0 TX packets:15557 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1913257 (1.8 MiB) TX bytes:3754172 (3.5 MiB) venet0:0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:212.72.124.87 P-t-P:212.72.124.87 Bcast:212.72.124.87 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 ======= (NOTE: The IP has been changed from actual output.) I believe instead of "lo" there should be an "eth1" -- can see that this is the case for the *old* Cobbler VPS that I migrated to OpenVZ, where dhcpd runs but where there is another problem. Frank _______________________________________________ cobbler mailing list [email protected] https://fedorahosted.org/mailman/listinfo/cobbler _______________________________________________ cobbler mailing list [email protected] https://fedorahosted.org/mailman/listinfo/cobbler
