I think I understand bridges a lot better now thanks to you. Thanks for the post and your research on this.
Bob Cochran On 7/12/11 6:03 PM, [email protected] wrote: > Alright so here is what I see. You have you are trying to setup your dhcpd > on a virtual interface and not a real interface. That will not work, you > need ARP to have dhcpd working. Look at this: > > http://forum.openvz.org/index.php?t=msg&goto=33837&; > > This will help you likely. > > Basically what your dhcp server is trying to do is run not on venet0:0 but on > venet0 for which you do not have subnet defined. You likely can test that by > defining the subnet of your vnet0. It may startup for you (but obviously > won't do anything useful). You will likely have to create a bridged > interface and put that. > > I suppose you can try to include the venet0 subnet in your dhcpd.conf and it > may work, I never tested it that way, but it be worth a shot just to see. > > > > Marek Dohojda > 720-308-8622 > > 77 68 6f 20 69 73 20 4a 6f 68 6e 20 47 61 6c 74 3f 0d 0a > > > -----Original Message----- > From: [email protected] > [mailto:[email protected]] On Behalf Of Frank > Sent: Tuesday, July 12, 2011 12:59 PM > To: cobbler mailing list > Subject: RE: *paid install help?*: Cobbler on a OpenVZ container / "dhcpd" > failing > >> /etc/sysconfig/dhcpd > # Command line options here > DHCPDARGS= > > > >> your ifconfig printout > > [root@cobbler sysconfig]# ifconfig > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > inet6 addr: ::1/128 Scope:Host > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:20670 errors:0 dropped:0 overruns:0 frame:0 > TX packets:20670 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:2331576 (2.2 MiB) TX bytes:2331576 (2.2 MiB) > > venet0 Link encap:UNSPEC HWaddr > 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 > inet addr:127.0.0.1 P-t-P:127.0.0.1 Bcast:0.0.0.0 > Mask:255.255.255.255 > UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 > RX packets:18501 errors:0 dropped:0 overruns:0 frame:0 > TX packets:15557 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:1913257 (1.8 MiB) TX bytes:3754172 (3.5 MiB) > > venet0:0 Link encap:UNSPEC HWaddr > 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 > inet addr:212.72.124.87 P-t-P:212.72.124.87 > Bcast:212.72.124.87 Mask:255.255.255.255 > UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 > > ======= > (NOTE: The IP has been changed from actual output.) > > I believe instead of "lo" there should be an "eth1" -- can see that > this is the case for the *old* Cobbler VPS that I migrated to OpenVZ, > where dhcpd runs but where there is another problem. > > Frank > _______________________________________________ > cobbler mailing list > [email protected] > https://fedorahosted.org/mailman/listinfo/cobbler > _______________________________________________ > cobbler mailing list > [email protected] > https://fedorahosted.org/mailman/listinfo/cobbler > _______________________________________________ cobbler mailing list [email protected] https://fedorahosted.org/mailman/listinfo/cobbler
