Hi - I'm CC'ing coreboot list again. On Wed, Jan 28, 2009 at 05:53:12PM +0200, Mart Raudsepp wrote: > Ühel kenal päeval, K, 2009-01-28 kell 17:43, kirjutas Mart Raudsepp: > > Ühel kenal päeval, K, 2009-01-28 kell 10:28, kirjutas Kevin O'Connor: > > > Debug level 20 tends to show all the irqs - which can adversely impact > > > the boot because of timing. So sending both the log from debug level > > > 20 and a log with debug level 8 would help. > > Trying with loglevel 8 > > Result: > > LAR: load_file: No such file 'normal/payload/segment1' > LAR: load_file_segments: All loaded, entry 0x000f7e6c > ========== mainboard_pre_payload: done > ========================================= > Start bios > init ivt > init bda > init pic > init timer > tsc calibrate start=2812945761 end=2813687197 diff=741436 > CPU Mhz=431 > math cp init > bios_table_addr: 0x000f8e30 end=0x000f9030 > Find memory size > Attempting to find coreboot table > Add to e820 map: 00000000 00000b84 2 > Add to e820 map: 00000b84 0009f47c 1 > Add to e820 map: 000f0000 000004b8 2 > Add to e820 map: 00100000 3eee0000 1 > Add to e820 map: 00000000 00004000 1 > init SMBIOS tables > SMBIOS table addr=0x000f8e30 > Add to e820 map: 000a0000 00050000 -1 > Add to e820 map: 0009fc00 00000400 2 > Add to e820 map: 000f0000 00010000 2 > Ram Size=0x3efe0000 > init PNPBIOS table > init keyboard > i8042_flush > i8042 flushed 000000ff (status=000000ff) > i8042 flushed 000000ff (status=000000ff) > i8042 flushed 000000ff (status=000000ff) > i8042 flushed 000000ff (status=000000ff) > i8042 flushed 000000ff (status=000000ff) > i8042 flushed 000000ff (status=000000ff) > i8042 flushed 000000ff (status=000000ff) > i8042 flushed 000000ff (status=000000ff) > i8042 flushed 000000ff (status=000000ff) > i8042 flushed 000000ff (status=000000ff) > i8042 flushed 000000ff (status=000000ff) > i8042 flushed 000000ff (status=000000ff) > i8042 flushed 000000ff (status=000000ff) > i8042 flushed 000000ff (status=000000ff) > i8042 flushed 000000ff (status=000000ff) > i8042 flushed 000000ff (status=000000ff) > i8042 timeout on flush
You appear not to have an i8042 controller (io ports 0x60/0x64). Which means you wont be able to use the keyboard. > init lpt > init serial > e820 map has 4 items: > 0: 0000000000000000 - 000000000009fc00 = 1 > 1: 000000000009fc00 - 00000000000a0000 = 2 > 2: 00000000000f0000 - 0000000000100000 = 2 > 3: 0000000000100000 - 000000003efe0000 = 1 > final bios_table_addr: 0x000f8f3a (used 51%) > init hard drives > ATA controller 0 at 000001f0/000003f0 (dev 0000007a prog_if 00000080) > ATA controller 1 at 00000170/00000370 (dev 0000007a prog_if 00000080) > ata_detect(1) drive=0 sc=00000055 sn=000000aa > ata_reset(1) status=00000080 > ata_reset(2) status=00000050 > ata_detect(2) drive=0 sc=00000001 sn=00000001 > ata_detect(3) drive=0 sc=00000001 sn=00000001 cl=00000000 ch=00000000 > st=00000050 > ata0-0: PCHS=7866/16/63 translation=large LCHS=983/128/63 > ata0 master: APACER CF SMI222AD ATA-0 Hard-Disk (3871 MiBytes) > ata_detect(1) drive=1 sc=00000055 sn=000000aa > ata_reset(1) status=00000080 > ata_reset(2) status=00000050 > ata_detect(2) drive=1 sc=00000001 sn=00000001 > ata_detect(3) drive=1 sc=00000001 sn=00000001 cl=00000000 ch=00000000 > st=00000000 > ata0 slave: Unknown device > ata_detect(1) drive=2 sc=000000ff sn=000000ff > ata_detect(1) drive=3 sc=000000ff sn=000000ff > > init boot device ordering > Press F12 for boot menu. > > Jump to int19 > Changing serial settings was 00000003/00000002 now 00000003/00000000 > enter handle_19: > NULL > Booting from Floppy... > fail floppy_13XX:729(00000001): > a=00000201 b=00000000 c=00000001 d=00000000 si=00000000 di=00000000 > ds=00000000 es=000007c0 ip=0000e3f8 cs=0000f000 f=00000002 r=00007b5e > Boot failed: could not read the boot disk > > enter handle_18: > NULL > Booting from CD-Rom... > CDROM boot failure code : 00000002 > Boot failed: could not read the boot disk > > enter handle_18: > NULL > Booting from Hard Disk... > Booting from 00000000:00007c00 > ata_reset(1) status=00000080 > ata_reset(2) status=00000050 > enter handle_12: > a=00000000 b=00000000 c=00000000 d=00000080 si=00002118 di=000042ec > ds=00000000 es=00000000 ip=000024c1 cs=00000000 f=00000297 r=00001fd2 > ata_reset(1) status=00000080 > ata_reset(2) status=00000050 > enter handle_12: > a=00000000 b=00000000 c=00000000 d=00000580 si=00002118 di=000541ec > ds=00000000 es=00000000 ip=00008a01 cs=00000000 f=00000297 r=00001fd2 > fail get_device:644(00000001): > a=00004100 b=000055aa c=0005425c d=00054281 si=00067fc0 di=00000081 > ds=00000000 es=00000000 ip=000088b5 cs=00000000 f=00000246 r=00001fd2 > fail get_device:644(00000001): > a=00000800 b=00000000 c=0005425c d=00054281 si=00067fc0 di=00000081 > ds=00000000 es=00000000 ip=000088e9 cs=00000000 f=00000246 r=00001fd2 > fail handle_15XX:313(00000086): > a=000000c0 b=00000000 c=00054201 d=00000001 si=00067fc0 di=00000000 > ds=00000000 es=00000000 ip=00008ab6 cs=00000000 f=00000246 r=00001fd2 > > > ... silence or hang Everything else looks okay. What is shown (if anything) on the screen at this point? -Kevin -- coreboot mailing list: [email protected] http://www.coreboot.org/mailman/listinfo/coreboot
