Hi Peter,
I m using Montavista Linux 2.6.10 (mvl402).
reboot code as mentioned in mail is executed properly.but then after
this line davinci_wdt->wdtcr = 0x00004000;, it doesn't execute next
statement (I tried with putting printk statement after it).
Doe it mean that it resets watchdog correctly.
But then it doesn't reset the processor & doesn't start execution of UBL
code again.
What can be the problem ?
Thanks,
Sweta
>
>
> Hi Sweta,
>
> which kernel are you using ?? It works with the 2.6.19 Kernel from GIT
> tree.
>
> Ciao,
>
> Peter
>
> On Thu, 28 Dec 2006, [EMAIL PROTECTED] wrote:
>
>>  Hi All,
>> I want to reset the Davinci pocessor using watchdog timer.
>> So when I give reboot command from kernel, it hangs & doesn't actually
>> reset the processor.
>> code for watchdog rest in kernel is as follows :
>> void davinci_watchdog_reset(void) {
>>         volatile davinci_timer_regs_t *davinci_wdt = (volatile
>> davinci_timer_regs_t *)IO_ADDRESS(DAVINCI_WDOG_BASE);
>>         davinci_wdt->tcr = 0x0;         /* disable timer */
>>         davinci_wdt->tgcr = 0x0;        /* reset timer */
>>         davinci_wdt->tgcr = 0x8;        /* configure timer2 as 64-bit */
>>         davinci_wdt->tgcr |= 0x3;       /* release timer from reset */
>>         davinci_wdt->tim12 = 0;         /* clear counter and period regs
>> */
>>         davinci_wdt->tim34 = 0;
>>         davinci_wdt->prd12 =  0;
>>         davinci_wdt->prd34 =  0;
>>         davinci_wdt->tcr   |= 0x00000040;
>>         davinci_wdt->wdtcr |= 0x4000;   /* enable watchdog timer */
>>
>>         *(volatile unsigned int *)(0x01c41a20) = 0x00000000;
>>
>>         /* put watchdog in pre-active state */
>>        davinci_wdt->wdtcr = 0xA5C64000;
>>
>>        /* put watchdog in active state */
>>        davinci_wdt->wdtcr = 0xDA7E4000;
>>
>>       /* write an invalid value to the WDKEY field to trigger* a
>> watchdog
>> reset */
>>           davinci_wdt->wdtcr = 0x00004000;
>>
>> }
>>
>> But it hangs & doesn't actually reset the processor.
>> I tried with reset commnad from u-boot loader also. It also gives me the
>> same  result.
>> Can anyone Help me out to debug what is wrong ?
>>
>> Thanks in advance,
>> -Sweta
>>




eInfochips Business Disclaimer:
This message may contain confidential, proprietary or legally Privileged 
information. In case you are not the original intended Recipient of the 
message, you must not, directly or indirectly, use, Disclose, distribute, 
print, or copy any part of this message and you are requested to delete it and 
inform the sender. Any views expressed in this message are those of the 
individual sender unless otherwise stated. Nothing contained in this message 
shall be construed as an offer or acceptance of any offer by eInfochips Limited 
and/or eInfochips Inc("eInfochips") unless sent with that express intent and 
with due authority of eInfochips. eInfochips has taken enough precautions to 
prevent the spread of viruses. However the company accepts no liability for any 
damage caused by any virus transmitted by this email.
_______________________________________________
Davinci-linux-open-source mailing list
[email protected]
http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source

Reply via email to