dear all:
when i run command make ARCH=arm CROSS_COMPILE=arm_v5t_le- checksetconfig,some
errors occurs:
#
# configuration written to .config
#
python /mnt/lsp/ti-davinci/linux-2.6.18_pro500/scripts/kconfig/checksetflags -z
-v --config-file .config --flag-file
/mnt/lsp/ti-davinci/linux-2.6.18_pro500/scripts/kconfig/baseconfig
Could not find platform independent libraries <prefix>
Could not find platform dependent libraries <exec_prefix>
Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>]
'import site' failed; use -v for traceback
Traceback (most recent call last):
File "/mnt/lsp/ti-davinci/linux-2.6.18_pro500/scripts/kconfig/checksetflags",
line 3, in ?
import os
ImportError: No module named os
make[1]: *** [checksetconfig] Error 1
make: *** [checksetconfig] Error 2
if i ignore these errors,I can compile and got a uImage,but it cann't boot up
linux too!
2009-05-15
zuowenping
发件人： B, Ravi
发送时间： 2009-05-15 11:47:43
收件人： JayaKumar, PremKumar; zuowenping; Deepak Mundra
抄送： davinci-linux-open-source
主题： RE: I can't boot linux2.6.18 uImage in dm355
Hi
Go to menuconfig, kernel Features-> select “allow old ABI binaries to run with
this kernel” or disable the “ARM EABI to compile the kernel”. Then do clean
build. This should resolve the issue.
Regards
Ravibabu
From: [email protected]
[mailto:[email protected]] On Behalf Of
JayaKumar, PremKumar
Sent: Friday, May 15, 2009 8:16 AM
To: zuowenping; Deepak Mundra
Cc: davinci-linux-open-source
Subject: RE: I can't boot linux2.6.18 uImage in dm355
I faced similar issue when switching between kernel builds for different
platforms. In such cases, a proper/full clean before build helped in getting
the right uImage built. Probably, you can try that too.
make distclean
make ARCH=arm CROSS_COMPILE=arm_v5t_le- davinci_dm355_defconfig
make ARCH=arm CROSS_COMPILE=arm_v5t_le- checksetconfig
make ARCH=arm CROSS_COMPILE=arm_v5t_le- uImage
Regards,
Prem
Texas Instruments
India
From: davinci-linux-open-source-bounces+premkumar.j=ti....@linux.davincidsp.com
[mailto:davinci-linux-open-source-bounces+premkumar.j=ti....@linux.davincidsp.com]
On Behalf Of zuowenping
Sent: Friday, May 15, 2009 6:39 AM
To: Deepak Mundra
Cc: davinci-linux-open-source
Subject: Re: Re: I can't boot linux2.6.18 uImage in dm355
thanks Deepak:
I have configed kernel by the command :
make ARCH=arm CROSS_COMPILE=arm_v5t_le- davinci_dm355_defconfig
make ARCH=arm CROSS_COMPILE=arm_v5t_le- uImage
use the default configs for dm355,the kernel can't been boot up,I have Enabled
kernel hacking->kernel debuging->low level debug functions.
the same result i goted! the envirment is:
software:DaVinciLSP_02_00_00_110 ,mvltools5_0_0801921
hardware: dm355 evm
and resut is as:
DM355 EVM # tftpboot
TFTP from server 10.0.0.89; our IP address is 10.0.0.53
Filename 'uImage'.
Load address: 0x80700000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
###########################################################
done
Bytes transferred = 1965512 (1dfdc8 hex)
DM355 EVM # bootm
## Booting image at 80700000 ...
Image Name: Linux-2.6.18_pro500-davinci_evm-
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1965448 Bytes = 1.9 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing
Linux...................................................................................................................................
It stoped here for ever! it seems no printed kernel information only uboot
prints,I have doubled where the serial configs have errors,I have checked the
bootargs whick can been used well for the uImage that comes with DVSDK.
setenv bootargs console=ttyS0,115200n8 noinitrd rw ip=dhcp root=/dev/nfs
nfsroot=10.0.0.89:/opt/montavista/pro/devkit/arm/v5t_le/target/,
nolock mem=116M video=davincifb:vid0=720x576x16,2500K:vid1=720x576x16,
2500K:osd0=720x576x16,2025K davinci_enc_mngr.ch0_output=COMPOSITE
davinci_enc_mngr.ch0_mode=$(videostd)
so it is not the bootargs error i think! serial driver error? board config
driver error? It amazed me so far!
2009-05-15
zuowenping
发件人： Deepak Mundra
发送时间： 2009-05-14 22:46:04
收件人： Steve Chen
抄送： zuowenping; davinci-linux-open-source
主题： Re: I can't boot linux2.6.18 uImage in dm355
Dear zuowenping
do make menuconfig
Enable kernel hacking->kernel debuging->low level debug functions
and compile the kernel and post the kernel output here
Regards
Deepak
On 5/14/09, Steve Chen <[email protected]> wrote:
On Thu, 2009-05-14 at 13:49 +0800, zuowenping wrote:
> My develop envirment :
> DaVinciLSP_02_00_00_110 ,mvltools5_0_0801921 and dm355 evm
> I have built the kernel by reference the pdf " TMS320DM355 DVEVM v1.30
> Getting Started Guide" ,
> DM355 EVM # printenv
> bootdelay=3
> baudrate=115200
> bootfile=uImage
> bootcmd=nboot 0x80700000 0 0x400000;bootm 0x80700000
> fileaddr=80700000
> ipaddr=10.0.0.53
> bootargs=console=ttyS0,115200n8 noinitrd rw ip=dhcp root=/dev/nfs
> nfsroot=10.0.0.89:/nfs/restore_dm355,nolock mem=116M
> video=davincifb:vid0=720x576x16,2500K:vid1=720x576x16,
> 2500K:osd0=720x576x16,2025K davinci_enc_mngr.ch0_output=COMPOSITE
> davinci_enc_mngr.ch0_mode=pal
> serverip=10.0.0.89
> filesize=2191c0
> stdin=serial
> stdout=serial
> stderr=serial
> videostd=pal
>
> Environment size: 491/16380 bytes
> why not success?
> Any clues will be appreciated!
Just want to make sure I understand, you can boot the board with the
binary that comes with DVSDK, but you can not boot the board with the
binary generated by following the "Getting Started Guide"
If that is the case, what are the commands you used to configure and
build the kernel and what error did you see during boot up?
Regards,
Steve
_______________________________________________
Davinci-linux-open-source mailing list
[email protected]
http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source
_______________________________________________
Davinci-linux-open-source mailing list
[email protected]
http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source
