Le Dimanche 28 Mai 2006 12:38, Nicolas Lécureuil a écrit :
> quand il ne se monte pas il faudrait asavoir ce que dis dmesg
ci-joint la réponse (un peu longue, mais je ne sais pas ce qui est important
ou pas: )
merci
BV
Linux version 2.6.12-22mdk ([EMAIL PROTECTED]) (gcc version 4.0.1
(4.0
.1-5mdk for Mandriva Linux release 2006.0)) #1 Tue May 23 17:26:47 MDT 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fe73000 (usable)
BIOS-e820: 000000000fe73000 - 000000000fe75000 (ACPI NVS)
BIOS-e820: 000000000fe75000 - 000000000fe94000 (ACPI data)
BIOS-e820: 000000000fe94000 - 000000000ff00000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
254MB LOWMEM available.
found SMP MP-table at 000fe710
On node 0 totalpages: 65139
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 61043 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 DELL ) @ 0x000fd530
ACPI: RSDT (v001 DELL 4500S 0x00000006 ASL 0x00000061) @ 0x000fd544
ACPI: FADT (v001 DELL 4500S 0x00000006 ASL 0x00000061) @ 0x000fd578
ACPI: SSDT (v001 DELL st_ex 0x00001000 MSFT 0x0100000d) @ 0xfffd7180
ACPI: MADT (v001 DELL 4500S 0x00000006 ASL 0x00000061) @ 0x000fd5ec
ACPI: BOOT (v001 DELL 4500S 0x00000006 ASL 0x00000061) @ 0x000fd648
ACPI: DSDT (v001 DELL dt_ex 0x00001000 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 0ff00000 (gap: 0ff00000:eed00000)
Built 1 zonelists
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
Kernel command line: auto BOOT_IMAGE=2612-22 root=305 resume=/dev/hda6
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 2000.481 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 253888k/260556k available (2357k kernel code, 6136k reserved, 719k
data,
260k init, 0k highmem, 0k BadRAM)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3964.92 BogoMIPS (lpj=1982464)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 3febfbff 00000000 00000000 00000000
00000000
00000000 00000000
CPU: After vendor identify, caps: 3febfbff 00000000 00000000 00000000 00000000
0
0000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: 3febfbff 00000000 00000000 00000080 00000000
0000000
0 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
mtrr: v2.0 (20020519)
CPU: Intel(R) Pentium(R) 4 CPU 2.00GHz stepping 04
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
checking if image is initramfs... it is
Freeing initrd memory: 120k freed
ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
ACPI: Looking for DSDT in initrd... not found.
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfbe4e, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:02.0
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 12 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11 12 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 9 10 11 12 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
PnPBIOS: Disabled
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:09: ioport range 0x800-0x85f could not be reserved
pnp: 00:09: ioport range 0xc00-0xc7f has been reserved
pnp: 00:09: ioport range 0x860-0x8ff could not be reserved
Simple Boot Flag value 0x87 read from CMOS RAM was invalid
Simple Boot Flag at 0x7a set to 0x1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1148783141.909:0): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch ([EMAIL PROTECTED])
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
PNP: PS/2 controller doesn't have AUX irq; using default 0xc
PNP: PS/2 Controller [PNP0303:KBD] at 0x60,0x64 irq 112
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
pktcdvd: v0.2.0a 2004-07-14 Jens Axboe ([EMAIL PROTECTED]) and [EMAIL PROTECTED]
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: ST340016A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: SAMSUNG CDRW/DVD SM-332B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes not supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 < p5 p6 p7 p8 >
mice: PS/2 mouse device common for all mice
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
NET: Registered protocol family 1
Using IPI Shortcut mode
PM: Checking swsusp image.
swsusp: Resume From Partition /dev/hda6
swsusp: Suspend partition has wrong signature?
swsusp: Error -22 check for resume file
PM: Resume from disk failed.
ACPI wakeup devices:
VBTN PCI0 USB0 USB1 USB2 PCI1 KBD
ACPI: (supports S0 S1 S3 S4 S5)
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
Freeing unused kernel memory: 260k freed
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
input: AT Translated Set 2 keyboard on isa0060/serio0
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000ff80
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000ff60
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ff40
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-1: new low speed USB device using uhci_hcd and address 2
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xffa00800
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
usb 4-5: new high speed USB device using ehci_hcd and address 3
usb 1-1: USB disconnect, address 2
usb 1-1: new low speed USB device using uhci_hcd and address 3
EXT3 FS on hda5, internal journal
SCSI subsystem initialized
usbcore: registered new driver hiddev
input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:1d.0-1
Initializing USB Mass Storage driver...
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1d.0-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
usbcore: registered new driver usbkbd
drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbmouse
drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
Adding 1124508k swap on /dev/hda6. Priority:-1 extents:1
hw_random: RNG not detected
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 845G Chipset.
agpgart: Detected 892K stolen memory.
agpgart: AGP aperture is 128M @ 0xf0000000
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Supermount version 2.0.4 for kernel 2.6
ntfs: Ignoring new-style parameters in presence of obsolete ones
NTFS driver 2.1.22 [Flags: R/O DEBUG MODULE].
NTFS volume version 3.1.
loop: loaded (max 8 devices)
hdc: ATAPI 40X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ip_conntrack version 2.1 (2035 buckets, 16280 max) - 260 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ACPI: Power Button (FF) [PWRF]
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
NET: Registered protocol family 17
Linux Tulip driver version 1.1.13 (May 11, 2002)
ACPI: PCI Interrupt 0000:01:08.0[A] -> GSI 17 (level, low) -> IRQ 17
tulip0: MII transceiver #1 config 1000 status 7869 advertising 01e1.
tulip0: MII transceiver #2 config 1000 status 786d advertising 01e1.
tulip0: MII transceiver #3 config 1000 status 786d advertising 01e1.
tulip0: MII transceiver #4 config 1000 status 786d advertising 01e1.
eth0: ADMtek Comet rev 17 at 0001ec00, 00:30:F1:3F:A1:B4, IRQ 17.
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, using FIFO
[PCSPP,TRISTATE,COMPAT,EC
P]
parport0: Printer, Samsung ML-4500
lp0: using parport0 (interrupt-driven).
lp0: console ready
lp0: ECP mode
lp0: ECP mode
lp0: ECP mode
0000:01:08.0: tulip_stop_rxtx() failed
eth0: Setting full-duplex based on MII#1 link partner capability of 45e1.
ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 50106 usecs
intel8x0: clocking to 48000
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03c9080(lo)
IPv6 over IPv4 tunneling driver
[drm] Initialized drm 1.0.0 20040925
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
[drm] Initialized i915 1.1.0 20040405 on minor 0:
mtrr: base(0xf0020000) is not aligned on a size(0x300000) boundary
eth0: no IPv6 routers present
NET: Registered protocol family 4
NET: Registered protocol family 5
usb 4-5: reset high speed USB device using ehci_hcd and address 3
scsi: Device offlined - not ready after error recovery: host 0 channel 0 id 0
lu
n 0
usb-storage: device scan complete
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
usb 4-5: USB disconnect, address 3
usb 4-5: new high speed USB device using ehci_hcd and address 4
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
usb 4-5: USB disconnect, address 4
usb 4-5: new high speed USB device using ehci_hcd and address 5
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
usb 4-5: reset high speed USB device using ehci_hcd and address 5
scsi: Device offlined - not ready after error recovery: host 2 channel 0 id 0
lu n 0
usb-storage: device scan complete
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
--
Les Bestioles en WouaB:
http://www.bertrand.vuarnesson.com/
=========================================
Vous souhaitez acquerir votre Pack ou des Services Mandriva?
Rendez-vous sur "http://store.mandriva.com";.
Rejoignez le club mandrake : http://www.mandrivaclub.com
=========================================
