I also use it and it is very good. Regards Leigh
On 24 August 2012 13:29, Kyley Harris <[email protected]> wrote: > I also use it.. an app with debugging at 25mb becomes about 5-6mb. its > excellent. > > On Thu, Aug 23, 2012 at 9:31 PM, Jeremy Coulter <[email protected]> wrote: >> >> You could also use UPXG which compresses and does some other bits and >> pieces >> to the exe to make it smaller. >> I have used it for at least 8 years and never had a problem. A 19mb exe >> goes >> to just over 6mb! >> >> Jeremy C. >> >> -----Original Message----- >> From: [email protected] >> [mailto:[email protected]] On Behalf Of Robo >> Sent: Thursday, 23 August 2012 17:25 >> To: NZ Borland Developers Group - Delphi List >> Subject: Re: [DUG] How to reduce size of Delphi XE2/DevExpress compiled >> exe? >> >> Thanks, do you know exactly where that is? >> >> Is it Component > Install Packages, then un-tick all the 'ExpressSkins >> Library Uses Clause AutoFill Helper'? >> >> Robo >> >> On Thu, Aug 23, 2012 at 5:13 PM, Jeremy North <[email protected]> >> wrote: >> > Make sure you don't have the 300 skins that come with devexpress >> > included. >> > >> > There is an option in the IDE to disabled them for a project or for all >> > time. >> > >> > >> > On Thu, Aug 23, 2012 at 2:53 PM, Colin Johnsun <[email protected]> >> wrote: >> >> >> >> Delphi XE2 carries over a lot of meta information for use with the >> >> RTTI. This may be the cause of the bloat in size. >> >> >> >> There are compiler options which you can use to switch it off. See the >> >> link below: >> >> >> >> >> >> >> >> http://delphi.about.com/b/2011/07/26/create-smaller-delphi-xe-executables-re >> move-rtti-pack-exe.htm >> >> >> >> Cheers, >> >> Colin >> >> >> >> On 23 August 2012 13:41, Robo <[email protected]> wrote: >> >> > If I compile the attached project in Delphi XE2, which only contains >> >> > a >> >> > blank form, I get a 7MB exe. >> >> > >> >> > If I start using DevExpress components, what used to be a 5MB exe in >> >> > Delphi 2005 turns into a 25MB exe in XE2. >> >> > >> >> > - What can I do to reduce the size? The blank project would have been >> >> > about 500KB in previous versions of Delphi. >> >> > - How can I keep the file size down when using DevExpress components? >> >> > >> >> > _______________________________________________ >> >> > NZ Borland Developers Group - Delphi mailing list >> >> > Post: [email protected] >> >> > Admin: http://delphi.org.nz/mailman/listinfo/delphi >> >> > Unsubscribe: send an email to [email protected] >> >> > with >> >> > Subject: unsubscribe >> >> _______________________________________________ >> >> NZ Borland Developers Group - Delphi mailing list >> >> Post: [email protected] >> >> Admin: http://delphi.org.nz/mailman/listinfo/delphi >> >> Unsubscribe: send an email to [email protected] with >> >> Subject: unsubscribe >> > >> > >> > >> > _______________________________________________ >> > NZ Borland Developers Group - Delphi mailing list >> > Post: [email protected] >> > Admin: http://delphi.org.nz/mailman/listinfo/delphi >> > Unsubscribe: send an email to [email protected] with >> > Subject: unsubscribe >> _______________________________________________ >> NZ Borland Developers Group - Delphi mailing list >> Post: [email protected] >> Admin: http://delphi.org.nz/mailman/listinfo/delphi >> Unsubscribe: send an email to [email protected] with >> Subject: unsubscribe >> >> _______________________________________________ >> NZ Borland Developers Group - Delphi mailing list >> Post: [email protected] >> Admin: http://delphi.org.nz/mailman/listinfo/delphi >> Unsubscribe: send an email to [email protected] with >> Subject: unsubscribe > > > > > -- > Kyley Harris > Harris Software > +64-21-671-821 > > _______________________________________________ > NZ Borland Developers Group - Delphi mailing list > Post: [email protected] > Admin: http://delphi.org.nz/mailman/listinfo/delphi > Unsubscribe: send an email to [email protected] with > Subject: unsubscribe _______________________________________________ NZ Borland Developers Group - Delphi mailing list Post: [email protected] Admin: http://delphi.org.nz/mailman/listinfo/delphi Unsubscribe: send an email to [email protected] with Subject: unsubscribe
