Woot! Great news, and thanks for all the time you've spent preparing all the RCs.
-ash > On 18 Dec 2017, at 20:13, Chris Riccomini <[email protected]> wrote: > > Hello, > > Apache Airflow (incubating) 1.9.0 (based on RC8) has been accepted. > > 5 “+1” binding votes received: > > - Maxime Beauchemin (binding) > - Chris Riccomini (binding) > - Bolke de Bruin (binding) > - Joy Gao (binding) > - Fokko Driesprong (binding) > > My next step is to open a thread with the IPMC. > > Cheers, > Chris > > On Mon, Dec 18, 2017 at 11:26 AM, Chris Riccomini <[email protected]> > wrote: > >> I believe so, yes. >> >> I will proceed with release. :) >> >> On Mon, Dec 18, 2017 at 11:20 AM, Bolke de Bruin <[email protected]> >> wrote: >> >>> But it doesn’t stop us from releasing now right? You can just update the >>> tag. It is not connected to the artifacts. >>> >>> Bolke. >>> >>> Sent from my iPhone >>> >>>> On 18 Dec 2017, at 18:51, Chris Riccomini <[email protected]> >>> wrote: >>>> >>>> https://github.com/apache/incubator-airflow/pull/2889 >>>> >>>> On Mon, Dec 18, 2017 at 9:44 AM, Chris Riccomini <[email protected] >>>> >>>> wrote: >>>> >>>>> Sigh. There's a catch 22 here. If we tag an RC as 1.9.0, we'll have to >>>>> keep editing the tag every time there's a new RC. I agree that >>> removing the >>>>> check seems like the best course of action. >>>>> >>>>> On Sun, Dec 17, 2017 at 12:01 AM, Bolke de Bruin <[email protected]> >>>>> wrote: >>>>> >>>>>> This is just matter of setting the tag in the repo right? >>>>>> >>>>>> We should remove that check or make it not fail at least. It is >>>>>> ridiculous. >>>>>> >>>>>> B. >>>>>> >>>>>> Verstuurd vanaf mijn iPad >>>>>> >>>>>>> Op 17 dec. 2017 om 07:32 heeft Joy Gao <[email protected]> het volgende >>>>>> geschreven: >>>>>>> >>>>>>> Ahh, tested the build on a fresh virtualenv, which succeeded *the >>> first >>>>>>> time* given gitpython was not installed and it skipped the assertion >>>>>> check >>>>>>> <https://github.com/apache/incubator-airflow/blob/1.9.0rc8/ >>>>>> setup.py#L68-L73>. >>>>>>> Build fails on re-installs :( >>>>>>> >>>>>>>> On Fri, Dec 15, 2017 at 6:01 PM, Feng Lu <[email protected] >>>> >>>>>> wrote: >>>>>>>> >>>>>>>> +0.5 (non-binding) >>>>>>>> >>>>>>>> Looks like the version(1.9.0) and tag(1.9.0rc8) is mismatched, >>>>>>>> <https://github.com/apache/incubator-airflow/blob/1.9.0rc8/ >>>>>> setup.py#L87> >>>>>>>> which will cause the installation (pip install or python setup) to >>>>>> error >>>>>>>> out and fail. >>>>>>>> nit: mind also updating the release log " >>>>>>>> https://github.com/apache/incubator-airflow/blob/1.9.0rc8/ >>>>>> CHANGELOG.txt" >>>>>>>> >>>>>>>> >>>>>>>> On Fri, Dec 15, 2017 at 3:21 PM, Driesprong, Fokko >>>>>> <[email protected]> >>>>>>>> wrote: >>>>>>>> >>>>>>>>> +1 binding >>>>>>>>> >>>>>>>>> Op vr 15 dec. 2017 om 23:39 schreef Bolke de Bruin < >>> [email protected] >>>>>>> >>>>>>>>> >>>>>>>>>> +1, binding >>>>>>>>>> >>>>>>>>>> Checked sigs, version, source is there (did not check build), bin >>> is >>>>>>>>> there. >>>>>>>>>> >>>>>>>>>> Bolke >>>>>>>>>> >>>>>>>>>> Verstuurd vanaf mijn iPad >>>>>>>>>> >>>>>>>>>>> Op 15 dec. 2017 om 23:31 heeft Joy Gao <[email protected]> het >>>>>> volgende >>>>>>>>>> geschreven: >>>>>>>>>>> >>>>>>>>>>> +1, binding >>>>>>>>>>> >>>>>>>>>>> Thank you Chris! >>>>>>>>>>> >>>>>>>>>>> On Fri, Dec 15, 2017 at 2:30 PM, Chris Riccomini < >>>>>>>>> [email protected]> >>>>>>>>>>> wrote: >>>>>>>>>>> >>>>>>>>>>>> Hey all, >>>>>>>>>>>> >>>>>>>>>>>> (Last time, I hope)^2 >>>>>>>>>>>> >>>>>>>>>>>> I have cut Airflow 1.9.0 RC8. This email is calling a vote on >>> the >>>>>>>>>> release, >>>>>>>>>>>> which will last for 72 hours. Consider this my (binding) +1. >>>>>>>>>>>> >>>>>>>>>>>> Airflow 1.9.0 RC8 is available at: >>>>>>>>>>>> >>>>>>>>>>>> https://dist.apache.org/repos/dist/dev/incubator/airflow/1.9 >>> .0rc8/ >>>>>>>>>>>> >>>>>>>>>>>> apache-airflow-1.9.0rc8+incubating-source.tar.gz is a source >>>>>>>> release >>>>>>>>>> that >>>>>>>>>>>> comes with INSTALL instructions. >>>>>>>>>>>> apache-airflow-1.9.0rc8+incubating-bin.tar.gz is the binary >>> Python >>>>>>>>>> "sdist" >>>>>>>>>>>> release. >>>>>>>>>>>> >>>>>>>>>>>> Public keys are available at: >>>>>>>>>>>> >>>>>>>>>>>> https://dist.apache.org/repos/dist/release/incubator/airflow/ >>>>>>>>>>>> >>>>>>>>>>>> The release contains no new JIRAs. Just a version fix. >>>>>>>>>>>> >>>>>>>>>>>> I also had to change the version number to exclude the `rc6` >>> string >>>>>>>> as >>>>>>>>>> well >>>>>>>>>>>> as the "+incubating" string, so it's now simply 1.9.0. This will >>>>>>>> allow >>>>>>>>>> us >>>>>>>>>>>> to rename the artifact without modifying the artifact checksums >>>>>> when >>>>>>>>> we >>>>>>>>>>>> actually release. >>>>>>>>>>>> >>>>>>>>>>>> See JIRAs that were in 1.9.0RC7 and before (see previous VOTE >>> email >>>>>>>>> for >>>>>>>>>>>> full list). >>>>>>>>>>>> >>>>>>>>>>>> Cheers, >>>>>>>>>>>> Chris >>>>>>>>>>>> >>>>>>>>>> >>>>>>>>> >>>>>>>> >>>>>> >>>>> >>>>> >>> >> >>
