It appears that when using the blewifi configuration out of the box, and
just turning on DEBUG_ASSERTIONS and DEBUG_ASSERTIONS_EXPRESSION, and
setting wifi ssid/pw causes the esp32 to hang. This is as far as I've
gotten so far. I'm still tweaking other configs to see if they cause
hanging as well.
This just does NOT appear to be a stable OS on the ESP32.
-m
On 8/31/2023 9:05 AM, Tiago Medicci Serrano wrote:
Hi!
Good to know that! Yes, there are packages that need to be selected to make
it work. The `esp32-devkitc:blewifi` is a good starting point.
Please note that BLE's log is enabled with the other wireless logs through
the menuconfig in "*Build Setup → Debug Options*". I hope this helps
debugging.
Best regards,
Em qua., 30 de ago. de 2023 às 18:29, Mike Moretti
<nu...@mordent.com.invalid> escreveu:
Hi,
Thanks. It wasn't until I untarred a whole new copy of nuttx+apps and
ran tools/configure.sh with blewifi that I was able to get that
configuration to work. In my old tree, make distclean apparently didn't
clean something, or my old tree was corrupt somehow.
However, I still cannot get my own config to work (the one I previously
attached). There's a lot more stuff I need enabled than what is enabled
by default in the blewifi configuration. I guess I will just have to
randomly keep modifying different config params until something works.
Thanks,
-m
On 8/30/2023 3:32 PM, Tiago Medicci Serrano wrote:
Hi Mike,
I found no trouble using the esp32-devkitc:blewifi configuration. May I
ask
you to double-check your bootloader/partition-table configuration? (you
can
refer to
https://nuttx.apache.org/docs/latest/platforms/xtensa/esp32/index.html#bootloader-and-partitions
).
If not successful yet, please do the following:
Select the esp32-devkitc:nxdiag configuration and run the `nxdiag -all`
from the NSH (please refer to
https://nuttx.apache.org/docs/latest/platforms/xtensa/esp32/boards/esp32-devkitc/index.html#nxdiag
).
Please share your results for reevaluattion ;)
Best regards,
Em ter., 29 de ago. de 2023 às 18:03, Tiago Medicci Serrano <
tiago.medi...@gmail.com> escreveu:
Hi,
I'll take a look at it soon. Interestingly, our internal CI tests all
the
defconfigs, so I wouldn't expect any erroneous behavior.
I'll check.
Best regards,
Em ter., 29 de ago. de 2023 às 16:38, Mike Moretti
<nu...@mordent.com.invalid> escreveu:
Hi,
I'm using NuttX 12.2.1 on an esp32 wroom devkit.
If I try to configure NuttX via tools/configure.sh using the
esp32-devkitc:blewifi configuration, when I boot the esp32, I get
problems
with it telling me there's no bootable app.
If I instead start with the esp32-devkitc:nsh configuration and add
wifi
and ble to it via menuconfig, I get only a little further. It gets
past
the entropy message and then I see "AB" and it hangs forever. With
all the
ble options disabled and only wifi configured by itself it actually
boots
into nsh after some time. (At first, I had a somewhat similar issue
with
nsh when wifi only is enabled and connection info wasn't defined in the
config file, where it would seem to hang and then finally show a
prompt.
It wasn't until I actually figured out about turning on CONFIG_DEBUG
"ERROR" for network/wireless that it showed me a bunch of errors during
boot and I knew it wasn't just hanging permanently and to just wait
for it
a bit to show an nsh prompt.)
However, there don't seem to be any config debug options for bluetooth.
I have no idea why it hangs as no messages are displayed and it never
shows
a prompt even after a half an hour. I've now spent hours messing with
various BLE configuration options with no luck. I'm including my
config
file in hope that someone might see something wrong with it.
Thanks,
-m
--
Mike Moretti
♩♫♫♩♪♩
--
Tiago Medicci Serrano
Embedded Software Engineer
MSc Electronics/Microelectronics
m: +55 (19) 981403886 <+55+(19)+981403886>
e: tiago.medi...@gmail.com
a: Campinas, Brazil
Follow me:
<https://www.linkedin.com/in/tiago-serrano-924458b6>
<https://github.com/tmedicci>
