Hi Chun-Yeow, I'm running a stripped version of ubuntu. I did check that area but no crashlogs
I just compiled another kernel from the git Master (3.2.0 r4) and applied the 2 patches ( you supplied earlier) to them. I can get a stable system again with ath9k/Authsae and no reboots I can also create a ath5k mesh without Authsae. Now when I use Authsae I get this from both nodes Unexpected error -22 (expected -107) nlerror, cmd 11, seq 1349139988: Invalid argument I have nohwcrpyt=1 for ath5k but still get this error. I have rebooted a few times to see if it would (magically) work. But no good. I know going backwards is probably not a great idea, but i wanted to make sure I wasn't going crazy. Fred On Mon, Oct 1, 2012 at 8:57 PM, Yeoh Chun-Yeow <[email protected]>wrote: > Hi, Fred, > > Did you try to look at the "/sys/kernel/debug/crashlog" to see what > happen once reboot, assuming you are using OpenWRT? > > ---- > Chun-Yeow > > On Tue, Oct 2, 2012 at 12:57 AM, David Fulgham > <[email protected]> wrote: > > We have this issue with our UBNT equipment (Rockets, NanoStations, > Bullets, > > etc.) as well. > > > > I've been out of the o11s loop for a while, and was hoping that this bug > was > > fixed by now. I will have our test network up and running again if you > need > > a place to play with new firmware. > > > > David Fulgham > > > > > > On Mon, Oct 1, 2012 at 9:29 AM, fred veldini <[email protected]> > wrote: > >> > >> I have tried low signal (-85) up to strong signal (-20) no difference as > >> long as the nodes see each other they reboot. If I take a node and > move it > >> out out the other nodes area so they don't hear each other the router > stays > >> running. As soon as I bring it back towards the 2nd router they > randomly > >> reboot. > >> > >> I have (6) alix3d2 boards with (6) Engenius EMP-8602 plus and (6) > Ubiquity > >> SR-71A > >> > >> The chip sets for the radios: SR-71a (AR9160) and EMP-8602 (AR5413) > >> > >> Thanks for your help > >> > >> Fred > >> > >> > >> > >> On Mon, Oct 1, 2012 at 12:13 AM, Thomas Pedersen <[email protected]> > >> wrote: > >>> > >>> On Sun, Sep 30, 2012 at 8:52 PM, fred veldini <[email protected]> > >>> wrote: > >>> > I did and nothing. the box just stops responding and reboots. no > error > >>> > messages after boot. > >>> > >>> Does this issue still only occur in low-signal conditions? Can you > >>> please provide some information on the host systems and ath9k chipsets > >>> so we can try to reproduce this on our end? > >>> > >>> Thanks, > >>> Thomas > >>> _______________________________________________ > >>> Devel mailing list > >>> [email protected] > >>> http://lists.open80211s.org/cgi-bin/mailman/listinfo/devel > >> > >> > >> > >> _______________________________________________ > >> Devel mailing list > >> [email protected] > >> http://lists.open80211s.org/cgi-bin/mailman/listinfo/devel > >> > > > > > > _______________________________________________ > > Devel mailing list > > [email protected] > > http://lists.open80211s.org/cgi-bin/mailman/listinfo/devel > > > _______________________________________________ > Devel mailing list > [email protected] > http://lists.open80211s.org/cgi-bin/mailman/listinfo/devel >
_______________________________________________ Devel mailing list [email protected] http://lists.open80211s.org/cgi-bin/mailman/listinfo/devel
