On Thu, Feb 11, 2021 at 12:26 AM Ayushman Mishra <ayushvidush...@gmail.com> wrote:
> I tested the environment ./source-builder/sb-check , it gave this > result: RTEMS Source Builder - Check, 6 (61dcadee0825) > Environment is ok > When I used ../source-builder/sb-set-builder > --prefix=/home/ayush/quickstart1/rtems/6 --target=sparc-rtems6 > --with-rtems-bsp=erc32 --with-rtems-tests=yes 6/rtems-sparc , it > started rebuilding and installing rtems-sparc tool suite ( just like > it did with this ../source-builder/sb-set-builder > --prefix=$HOME/quick-start/rtems/5 5/rtems-sparc , and took same > amount of time to complete the process) but no erc32 bsp was installed > ( bsp test said error: no executables supplied) , and using > 6/rtems-kernel instead of 6/rtems-sparc it gives same Build error (pax > is missing) , right now rsb is only working properly for rtems5 and > not rtems6 on my system. > RSB builds the tools required to build rtems erc32 is a sparc BSP for building a BSP follow this : https://docs.rtems.org/branches/master/user/installation/kernel.html > > On Wed, Feb 10, 2021 at 11:44 AM Eshan Dhawan <eshandhawa...@gmail.com> > wrote: > > > > > > > > On Wed, Feb 10, 2021 at 10:36 AM Ayushman Mishra < > ayushvidush...@gmail.com> wrote: > >> > >> Thanks for the help Eshan but actually I have already performed this > >> step (sudo apt-get build-dep build-essential gcc-defaults g++ gdb git > >> \ > >> unzip pax bison flex texinfo unzip python3-dev libpython-dev \ > >> libncurses5-dev zlib1g-dev) , here since my system was not able to > >> find libpython-dev (Unable to find a source package for libpython-dev > >> ) so i used libpython2.7-dev , I tried with both python2-dev and > python3-dev > >> ( > >> sudo apt-get build-dep build-essential gcc-defaults g++ gdb git \ > >> unzip pax bison flex texinfo unzip python2-dev libpython2.7-dev \ > >> libncurses5-dev zlib1g-dev > >> Reading package lists... Done > >> Picking 'gcc-defaults' as source package instead of 'g++' > >> Picking 'python-defaults' as source package instead of 'python2-dev' > >> Picking 'python2.7' as source package instead of 'libpython2.7-dev' > >> Picking 'ncurses' as source package instead of 'libncurses5-dev' > >> Picking 'zlib' as source package instead of 'zlib1g-dev' > >> Reading package lists... Done > >> Building dependency tree > >> Reading state information... Done > >> 0 upgraded, 0 newly installed, 0 to remove and 184 not upgraded. > >> ) , > > > > did you test the environment > > > > ./source-builder/sb-check > >> > >> but then also same Build FAILED error comes up (configure: error: pax > >> is missing) . Also I wanted to know does the rsb in rtems6 uses > >> autoconf-based build system , since there is no configure file made > >> and used. > > > > Also, try using > > > > ../source-builder/sb-set-builder > --prefix=/home/ayush/quickstart1/rtems/6 --target=sparc-rtems6 > --with-rtems-bsp=erc32 --with-rtems-tests=yes 6/rtems-sparc > > > >> > >> On Wed, Feb 10, 2021 at 1:04 AM Eshan Dhawan <eshandhawa...@gmail.com> > wrote: > >> > > >> > Hi ayushman > >> > It looks you didn't install all the dependencies required > >> > check this : > https://docs.rtems.org/branches/master/user/hosts/posix.html#linux > >> > > >> > On Wed, Feb 10, 2021 at 12:58 AM Ayushman Mishra < > ayushvidush...@gmail.com> wrote: > >> >> > >> >> Ayusman Mishra > >> >> 1. I was going through ticket #4145 > >> >> (https://devel.rtems.org/ticket/4145) and tried building bsp on > rtems6 > >> >> and rtems5 both using rsb > >> >> ( > https://docs.rtems.org/branches/master/user/start/bsp-build.html#rsb-bsp-build > ) > >> >> but got Build FAILED (it says pax is missing (configure: error: pax > is > >> >> missing.), I have attached full error report txt file). However I did > >> >> build bsp erc32 and pc386 using rsb on rtems5 (first .bootstrap -c > >> >> sb-bootstrap then used configure file > >> >> ($HOME/development/rtems/rtems-5/configure --target=i386-rtems5 > >> >> --enable-rtemsbsp=pc386 )) on rtems6 there is no sb-bootstrap file or > >> >> configure file present/made. > >> >> I wanted to know is there anyway of using RSB on rtems6. > >> >> Also while building different bsp toolsets for rtems (erc32/pc386) I > >> >> used rtems on 2 different directories , Is there any way of building > >> >> different BSPs on same rtems? > >> >> > >> >> 2. I went through list of open projects and found projects related to > >> >> testing and development of ecosystem quite interesting, > >> >> #3710 https://devel.rtems.org/ticket/3710 > >> >> #3860 https://devel.rtems.org/ticket/3860 > >> >> #3892 https://devel.rtems.org/ticket/3892 > >> >> I would be very grateful to know if any of the above projects is open > >> >> for participation and if yes then work done/needed to be done in it. > >> >> _______________________________________________ > >> >> devel mailing list > >> >> devel@rtems.org > >> >> http://lists.rtems.org/mailman/listinfo/devel > >> > > >> > > >> > > >> > -- > >> > Thanks > >> > - Eshan >
_______________________________________________ devel mailing list devel@rtems.org http://lists.rtems.org/mailman/listinfo/devel