On Thu, Jul 03, 2014 at 09:12:49AM +0200, Marc Kleine-Budde wrote:
> On 07/03/2014 05:48 AM, Dong Aisheng wrote:
> > On Wed, Jul 02, 2014 at 09:13:07PM +0200, Marc Kleine-Budde wrote:
> >> On 07/02/2014 07:54 PM, Oliver Hartkopp wrote:
> >>> I'm not really familiar with the naming concept in device trees.
> >>>
> >>> What is your opinion about the remarks below?
> >>
> >> The entries in the DT, at least on freescale baords, follow the naming
> >> scheme of the reference manual. E.g. on the mx25 it's can1 and can2:
> >>
> >> can1: can@43f88000 { ... }
> >> can2: can@43f8c000 { ... }
> >>
> >> And on the mx28, its:
> >>
> >> can0: can@80032000 { ... }
> >> can1: can@80034000 { ... }
> >>
> >> Because the imx25 datasheet uses a "1" based counting scheme, while the
> >> imx28 uses a "0" based one.
> >>
> >> So it's best practise to follow the naming and numbering scheme of the
> >> hardware reference manual.....and if you have access to the
> >> documentation of the m_can core, use clock names of the m_can core for
> >> the clock-names property.
> >>
> >
> > Based on my knowledge, device tree allows define phandle name according to
> > the real device name of HW according spec while the device node name should
> > be general(e.g can@80032000 rather than flexcan@80032000).
> > For imx6sx, there are already following entries in
> > arch/arm/boot/dts/imx6sx.dtsi
> > flexcan1: can@02090000 {...}
> > flexcan2: can@02094000 {...}
> > So i'd prefer to define as:
> > m_can1: canfd@020e8000 {...}
> > m_can2: canfd@020f0000 {...}
> >
> >
> > One problem is there're can alias already.
> > aliases {
> > can0 = &flexcan1;
> > can1 = &flexcan2;
> > ...
> > }
> > I'm not sure adding can2&can3 for mcan is properly:
> > aliases {
> > can0 = &flexcan1;
> > can1 = &flexcan2;
> > can2 = &m_can1;
> > can3 = &m_can2;
> > ...
> > }
> > Since the m_can driver does not need to use aliases,
> > so i will not add them.
>
> IMHO It's fine too add the can{2,3} aliases to m_can, too.
>
I think the main problem for doing this way is that the meaning of id
return by of_alias_get_id may be not persistent.
e.g
For MX6SX
aliases {
can0 = &flexcan1;
can1 = &flexcan2;
can2 = &m_can1;
can3 = &m_can2;
...
}
For other platform, it could be:
aliases {
can0 = &m_can1;
can1 = &m_can2;
...
}
It's hard for driver to use.
And actually the M_CAN driver does not need to use the alias.
So i wonder if it makes sense to add the alias for m_can devices
like that.
Regards
Dong Aisheng
> Marc
>
> --
> Pengutronix e.K. | Marc Kleine-Budde |
> Industrial Linux Solutions | Phone: +49-231-2826-924 |
> Vertretung West/Dortmund | Fax: +49-5121-206917-5555 |
> Amtsgericht Hildesheim, HRA 2686 | http://www.pengutronix.de |
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
