ok sir then i'l try to debug the problem in my os now Thanks Sandhya
On Mon, Oct 21, 2013 at 11:49 AM, Activecat <[email protected]> wrote: > As I mentioned in previous email (below), the first thing you need to do > now is to bring up the physical layer of the Ethernet connection. > If the GE port LED is not ON, no point to proceed without this being > solved first. > > If you insist that your hardware support 1000Mbps GE, then make the Linux > recognise this first before troubleshooting at the gnuradio level. > > Now you should troubleshoot your Linux, not gnuradio, if you confirmed > that your hardware is really GE capable. > > > ---------- Forwarded message ---------- > From: Activecat <[email protected]> > Date: Mon, Oct 21, 2013 at 1:09 PM > Subject: Re: [Discuss-gnuradio] setup of usrp N100/N200 > To: Sandhya G <[email protected]> > Cc: [email protected] > > You shall troubleshoot in the following steps: > > 1). Bring up the physical ethernet connection between your PC and the > USRP. Upon successful you will see the LED turns on at the USRP GE port. > > 2). Set your PC IP address to the same subnet but don't crash with the > USRP's ip address. > If this step is successful then you will be able to ping the USRP. > > 3). Issue command "uhd_find_devices" and you will see the USRP being > discovered. > > Then you could proceed with "uhd_usrp_probe" to see more details. > > > On Mon, Oct 21, 2013 at 2:02 PM, Sandhya G <[email protected]> wrote: > >> OS is linux. my pc is 2010 model,has >> >> - 3rd Generation Intel® Core™ i5-3317U >> - 64-bit. >> >> And when i give the command sudo ethtool eth1 i'am getting the speed has >> 10Mb/s >> >> Settings for eth1: >> Supported ports: [ TP MII ] >> Supported link modes: 10baseT/Half 10baseT/Full >> 100baseT/Half 100baseT/Full >> Supported pause frame use: No >> Supports auto-negotiation: Yes >> Advertised link modes: 10baseT/Half 10baseT/Full >> 100baseT/Half 100baseT/Full >> Advertised pause frame use: Symmetric Receive-only >> Advertised auto-negotiation: Yes >> Speed: 10Mb/s >> Duplex: Half >> Port: MII >> PHYAD: 0 >> Transceiver: internal >> Auto-negotiation: on >> Supports Wake-on: pumbg >> Wake-on: g >> Current message level: 0x00000033 (51) >> drv probe ifdown ifup >> Link detected: no >> >> And ya GE port led is not ON >> >> Thanks >> >> Sandhya >> >> >> >> >> >> >> On Mon, Oct 21, 2013 at 11:04 AM, Activecat <[email protected]> wrote: >> >>> What operating system are you running, is it Linux or Microsoft Windows? >>> >>> >>> On Mon, Oct 21, 2013 at 1:25 PM, Sandhya G <[email protected]>wrote: >>> >>>> i'm seeing only LED's D and F are on, because host pc is not at all >>>> detecting the hardware and i'm unable to run any operation.In my first i >>>> mentioned the errors what i'am getting when i run the flowgraph. >>>> Even i'am clueless how my device is only showing up 10/100Mbps when i >>>> connect the hardware and even i tried with other pc but i'm facing the same >>>> problem. >>>> >>>> >>>> Thanks and regards >>>> Sandhya >>>> >>>> >>>> On Mon, Oct 21, 2013 at 10:42 AM, Activecat <[email protected]>wrote: >>>> >>>>> What operating are you running? How do you get the "10/100Mbps" ? Do >>>>> you see the LED turns on at the USRP GE port? >>>>> >>>>> >>>>> On Mon, Oct 21, 2013 at 1:09 PM, Sandhya G <[email protected]>wrote: >>>>> >>>>>> Sir my pc is capable of supporting 1000Mbps but when i connect the >>>>>> hardware and check the speed of the port it will be showing 10/100Mbps. >>>>>> What might the issue?and can i boost the pc speed >>>>>> >>>>>> Thanks and regards >>>>>> Sandhya >>>>>> >>>>>> >>>>>> On Mon, Oct 21, 2013 at 10:30 AM, Sandhya G <[email protected]>wrote: >>>>>> >>>>>>> ya its a new one and sir y i'am i getting unknown key format even >>>>>>> though i give addr=192.168.10.2 and the problem i'm facing is its >>>>>>> showing >>>>>>> me an error has cannot find as a single device.I have no clue the reason >>>>>>> for that >>>>>>> >>>>>>> Thanks and regards >>>>>>> Sandhya >>>>>>> >>>>>>> >>>>>>> On Mon, Oct 21, 2013 at 10:24 AM, Activecat <[email protected]>wrote: >>>>>>> >>>>>>>> If that is a new USRP from factory then you don't need to update >>>>>>>> the firmware. >>>>>>>> >>>>>>>> >>>>>>>> >>>>>>>> On Mon, Oct 21, 2013 at 12:51 PM, Sandhya G >>>>>>>> <[email protected]>wrote: >>>>>>>> >>>>>>>>> Thanks for the reply. >>>>>>>>> Well is that only problem so that i'm unable to communicate and >>>>>>>>> should i need to update the firmware? >>>>>>>>> >>>>>>>>> >>>>>>>>> Thanks and regards >>>>>>>>> Sandhya.G >>>>>>>>> >>>>>>>>> >>>>>>>>> On Mon, Oct 21, 2013 at 10:19 AM, Activecat >>>>>>>>> <[email protected]>wrote: >>>>>>>>> >>>>>>>>>> Your pc must have 1000Mbps port. The 10/100Mbps won't work. >>>>>>>>>> An alternative is to connect a 10/100/1000 LAN switch between >>>>>>>>>> your pc and the USRP. >>>>>>>>>> >>>>>>>>>> Rgds, >>>>>>>>>> activecat. >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> On Mon, Oct 21, 2013 at 12:37 PM, Sandhya G < >>>>>>>>>> [email protected]> wrote: >>>>>>>>>> >>>>>>>>>>> HI all, >>>>>>>>>>> >>>>>>>>>>> >>>>>>>>>>> I have followed as per the instructions given in the webpage for >>>>>>>>>>> set up of the Usrp N200/N210 but still i am unable to communicate >>>>>>>>>>> between >>>>>>>>>>> the hardware and host pc >>>>>>>>>>> >>>>>>>>>>> >>>>>>>>>>> >>>>>>>>>>> 1.I have set the static ip of the host pc to >>>>>>>>>>> 192.168.10.1(ifconfig eth0 192.168.10.1). >>>>>>>>>>> >>>>>>>>>>> 2.Whenever i give the device address=addr=192.168.10.1 and run >>>>>>>>>>> the grc i am getting the error has “*unknown key format*” >>>>>>>>>>> >>>>>>>>>>> 3.Whenever i ping 192.168.10.2 or use the command >>>>>>>>>>> uhb_find_device i am getting warning as “*NO DEVICE FOUND* “ >>>>>>>>>>> >>>>>>>>>>> 4. Is that a must i have to upload the fpga and firmware images >>>>>>>>>>> when using the device for the first time. >>>>>>>>>>> >>>>>>>>>>> 5.Sometimes i am getting an error like”* unable to find as >>>>>>>>>>> single device”.* >>>>>>>>>>> >>>>>>>>>>> *6.*The* *host pc is supporting only 10/100MBPS .Is that the >>>>>>>>>>> only problem so that i am unable to communicate with the hardware. >>>>>>>>>>> >>>>>>>>>>> >>>>>>>>>>> >>>>>>>>>>> Can anybody help me on this issue.Awaiting for your valuable >>>>>>>>>>> reply >>>>>>>>>>> >>>>>>>>>>> >>>>>>>>>>> Thanks in advance >>>>>>>>>>> >>>>>>>>>>> Sandhya.G >>>>>>>>>>> >>>>>>>>>>> _______________________________________________ >>>>>>>>>>> Discuss-gnuradio mailing list >>>>>>>>>>> [email protected] >>>>>>>>>>> https://lists.gnu.org/mailman/listinfo/discuss-gnuradio >>>>>>>>>>> >>>>>>>>>>> >>>>>>>>>> >>>>>>>>> >>>>>>>> >>>>>>> >>>>>> >>>>> >>>> >>> >> >
_______________________________________________ Discuss-gnuradio mailing list [email protected] https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
