Thanks, but I'm just doing the bits that I can with my skills/resources. So many others are contributing money to or doing the big electrical renos / management / accounting / volunteering / organizing and manning CTFs or events / setting up and explaining the 3d printer as you are. I think of it as a my thanks to skullspace and its members for being a great place.
On 5/19/13, Benjamin Bergman <[email protected]> wrote: > Thanks for all your work on this Colin. You have gone above and beyond. > On May 19, 2013 11:24 AM, "Colin Stanners" <[email protected]> wrote: > >> If anyone (Zewwy / Kenny / Adrian?) has time to help me with wiring this >> week, let me know. >> >> >> Wiring >> ----------- >> Done: 6x wires from above-bathrooms to downstairs door >> Done: 5x wires from server rack to above-bathrooms >> Done: 3x wires from above-bathroom to end of classroom >> Almost done: 6x from server rack to roof - need to tension guy >> lines >> better, trim zipties. >> Todo: 3x wires from server rack to lounge switch, main wifiAP on >> lounge ceiling, and VGAoCAT5 for projector >> Todo: 2x wires from server rack to workbench and middle table area >> >> Server area needs more wire clean-up, wires patched down to panel and >> labeled. >> To be done correctly, in some places (horizontal runs) cabling needs to >> be >> held by metal, not plastic. >> Later I'll put together a shopping list and plans to get old runs >> corrected. >> >> Doorbell >> ------------ >> Todo: Need to setup relay so the bell will ring when the card access >> system's power is disconnected. >> >> >> Touchscreens >> ------------ >> Thor, Jeremy and Mark are working on getting the correct serial >> touchscreen driver. After that we >> can set them up inside/outside the space as terminals for calendar etc. >> >> >> Cameras >> ------------- >> Installed 9: N+S rear parking lot; back door; elevator; outside Sksp2 >> door; outside front door; >> inside front door; N part of front street; roof view incl. internet >> antenna >> >> They're accessible from http://IP.skullspace.ca:81 >> >> I bought a 1x4 VGA splitter from Monoprice and eBay VGAoverCAT5 adapters* >> so that the view from the security PC can be sent to the currently-unused >> second VGA inputs on the projectors. Still waiting for the adapters. >> >> >> Documentation >> ------------- >> I need to label wires; also update the networking wiki page, but my login >> for the wiki is on a laptop 3ft >> away from me right now (didn't install VNC server on it) and getting >> there >> is work. >> >> >> Projectors >> ----------- >> Sksp lounge: I'm getting the same MP stand so it can be roof-mounted too. >> >> Classroom: need to install wire guide to make VGA run nicer. >> >> Both of these will have a line from the VGA splitter delivered over cat5. >> >> >> Main Sksp2 door >> ----------- >> Doesn't always shut automatically as the frame is tight - I think it just >> needs a bit of wedging apart in some places >> >> >> Network upgrades >> ---------- >> We've had the hardware to upgrade the 10x4mbit backup AW link to >> 100x100mbit >> since the beginning but it's quite a few hours to >> setup/configure/install, >> low priority. >> >> High-end HP 2.4+5.xGhz wifi AP was donated by Nate (now is the >> "skullspace" SSID), need to find/print a mount for the ceiling. >> >> Should setup a PC (Zewwy's?) running MRTG to log traffic statistics on >> all >> switch ports, >> maybe even local temperature and network rack power usage (measured at >> UPSes). >> >> Will soon get a new sksp main internal router (Mikrotik RouterBoard 450G) >> and change the 192.168.1.x net >> to below. This'll allow VPNing in, separate networks, redundant uplinks, >> QOS, also IPv6. >> 172.30.4.x = testing/reserved for later use (you may notice all of >> these are within a /22) >> 172.30.5.x = Security/Management network router .1 hosts .10-.29 >> DHCP .100-.250 >> 172.30.6.x = Main network DHCP .100-.250 router .1 network gear >> .10-.39 printers .40-.49 VMs, servers .50-.79 >> 172.30.7.x = CTF Network DHCP .100-.250 router .1 >> >> >> Internal web page >> ------------- >> The one I did for AW with links to all device web interfaces is useful, >> will make one for Sksp after re-ip. >> >> >> Card access control >> ----------- >> VM is working well, some final tests and fixes to do before remote access >> is complete. >> >> >> Skullspace door: allowing landlord access and easy exit >> --------- >> I got a motion detector from eBay to allow auto-unlocking when >> people get close to the door inside, but in the process of converting its >> relay >> from connecting the positive terminal to connecting the negative terminal >> I seem to have broken something since now it won't un-detect after boot. >> Got a different one that I'll try to setup. >> >> Door access for landlord/staff without keyfob: may be possible to move >> the >> current deadbolt to the "main" doorknob to make it work, but this is >> far on my to-do list right now, or $500 to get done by a locksmith. >> This would also allow exit without needing to push a button - preferable. >> >> Another option people mentioned would be a keypad at the door - this is >> easy >> and cheap to do but I'd rather have the standard key option. >> >> >> UPSes >> ------------- >> Square 600VA unit has a dying battery, will move the machines (Mak's and >> Ayecee's IIRC) off it. >> Nate's huge unit (always funny saying that) reports a battery error, I'll >> check wiring. >> >> >> Hooking access control to fire alarm for auto-release: >> ------------- >> Should be easily doable, I need to check what is required. >> >> _______________________________________________ >> SkullSpace Discuss Mailing List >> Help: http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >> Archive: https://groups.google.com/group/skullspace-discuss-archive/ >> > _______________________________________________ SkullSpace Discuss Mailing List Help: http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss Archive: https://groups.google.com/group/skullspace-discuss-archive/
