FWIW... I use my Microham interface like this... it can set up two virtual ports for CAT and works perfectly with my Icoms. I have had DX4Win and MixW or DX4Win and HRD working simultaneously with no problems at all.
ON4AOI wrote: > Hi Tibor, > Tried this out a few months ago before the bandmap was in DX4WIN. > I used bandmaster from VE3NEA,DX4WiN and HRD to see if the VSPE > Driver could handle it, I could make it working but very unstable, > Saved configuration did not work correct after shutting down and restarting > So everytime I had to reconfigure all, shortly after my tests the developing > In dx4win has started...... > > Guy ON4AOI > >> -----Oorspronkelijk bericht----- >> Van: [email protected] [mailto:dx4win- >> [email protected]] Namens Tibor M. Blum - IK2SAI - >> Verzonden: zondag 23 augustus 2009 11:56 >> Aan: [email protected] >> Onderwerp: [Dx4win] A strange thing >> >> Hy guys. >> >> My set up is a TS2000X with CAT made via Ham Radio Deluxe. >> >> Connection Is made with a serial/USB converter @ 57600 >> >> PC is an AMD Athlon @ 1 GHz, 640 RAM and Win XP sp3 >> >> >> >> Of course if I try to connect DX4WIN to my radio, PC says that the com >> is >> busy. >> >> If I connect DX4WIN without running Ham Radio Deluxe, all is ok, band >> map is >> ok, no problem. >> >> >> >> Yesterday in a forum someone talked to me about Virtual Serial Ports >> Emulator freeware software (VSPE). >> >> I immediately installed the software and after some minutes I was able >> to >> create a virtual com where to address Dx4WIN AND HRD. >> >> Fantastic: when I receive a spot I click on that, it change me the >> setting >> of the radio, HRD show all the new parameters and in the Dx4WIN I get >> the >> call in the right place. >> >> All works ok.BUT: >> >> Looking at the band map, it flickers: the vertical, qrg line moves from >> left >> to right and than again right to left. >> >> The frequency showed on the top of band map start from the right one >> and >> step by step goes down..down..down to zero.without moving the real QRG >> on >> the radio. >> >> On the QSO input window, the same happen in the frequency display. But >> even >> the mode and the band are changing step by step without sense. >> >> I tried to set the radio on 18140 SSB, on the band map the frequency >> starts >> to move down. In the QSO window problem is that the mode changes to CW, >> and >> so on and even the qrg moves. If I log the "qso" dx4win doesn't get the >> real >> data but what is displaying at that time. >> >> >> >> I have tried to reduce the com speed down to 9600 but nothing has >> changed. >> >> >> >> So I returned to my old setting.but there is any way to fix the >> problem? >> >> >> >> HRD + DX4WIN are just the best of the two worlds and being able to run >> them >> connected to the radio is certainly fantastic. >> >> >> >> Tibor, IK2SAI >> >> >> >> ______________________________________________________________ >> Dx4win mailing list >> Home: http://mailman.qth.net/mailman/listinfo/dx4win >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:[email protected] >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html > > ______________________________________________________________ > Dx4win mailing list > Home: http://mailman.qth.net/mailman/listinfo/dx4win > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > ______________________________________________________________ Dx4win mailing list Home: http://mailman.qth.net/mailman/listinfo/dx4win Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
